583276

Black Decker GL652 T3 Manual

8
Zoom out
Zoom in
Previous page
1/84
Next page
8
ENGLISH
Fittinganewspoolofcuttingline(g.G&H)
Replacement spools of cutting line are available from your
Black & Decker dealer (cat. no. A6441). Complete cassettes
containing a spool of cutting line are also available
(cat. no. A6442).
u Unplug the tool.
u Keep the tabs (17) depressed and remove the spool cover
(18) from the housing (11) (g. G).
u Remove the empty spool (19) from the spool cover.
u Remove any dirt and grass from the spool cover and
housing.
u Take the new spool and push it onto the boss in the spool
cover. Rotate the spool slightly until it is seated.
u Unclip the end of one of the cutting lines and guide the
line into one of the eyelets (20) (g. H). The line should
protrude approx. 11 cm from the spool cover.
u Unclip the end of the other cutting line and guide the line
into the other eyelet. The line should protrude approx.
11 cm from the spool cover.
u Align the tabs (17) on the spool cover with the cut outs
(21) in the housing (g. G).
u Push the cover onto the housing until it snaps securely
into place.
Warning! If the cutting lines protrude beyond the trimming
blade (10), cut them off so that they just reach the blade.
Windingnewlineontoanemptyspool(g.I,J&K)
You may wind new cutting line onto an empty spool.
Replacement packs of cutting line are available from your
Black & Decker dealer (cat. no. A6440).
u Remove the empty spool from the tool as described above.
u Remove any remaining cutting line from the spool.
u First wind new line onto the uppermost part of the spool:
- Feed 2 cm of cutting line into one of the slots in the
upper section of the spool as shown.
- Wind the cutting line onto the spool in the direction of
the arrow. Make sure to wind the line on neatly and in
layers. Do not criss-cross.
- When the wound cutting line reaches the recesses (23),
cut the line.
- Temporarily park the line in the slots (22) on one side of
the spool as shown.
u Repeat the above procedure for the second cutting line on
the lower section of the spool. Park the line in the unused
slots (22).
u Proceed as described above to t the spool on the tool.
Do not forget to release the cutting line from the parking
slots (22).
Warning! Only use the appropriate type of Black & Decker
cutting line. Ensure that cutting line is present in both sections
of the spool (g. K).
Mainsplugreplacement(U.K.&Irelandonly)
If a new mains plug needs to be tted:
u Safely dispose of the old plug.
u Connect the brown lead to the live terminal in the new plug.
u Connect the blue lead to the neutral terminal.
Warning! No connection is to be made to the earth terminal.
Follow the tting instructions supplied with good quality plugs.
Recommended fuse: 5 A.
Troubleshooting
If your tool seems not to operate properly, follow the
instructions below. If this does not solve the problem,
please contact your local Black & Decker repair agent.
Warning! Before proceeding, switch off and unplug the tool.
Tool runs slowly
u Check that the spool housing can rotate freely.
Carefully clean it if necessary.
u Check that the cutting line does not protrude more than
11 cm from the spool housing. If it does, cut it off so that it
just reaches the line trimming blade.
Automatic line feed does not work
u Keep the tabs depressed and remove the spool cover
from the housing.
u Pull the cutting line until it protrudes 11 cm from the
housing. If insufcient cutting line is left on the spool,
install a new spool of cutting line as instructed above.
u Align the tabs on the spool cover with the cut outs in the
housing.
u Push the cover onto the housing until it snaps securely
into place.
u If the cutting line protrudes beyond the trimming blade,
cut it off so that it just reaches the blade.
If the automatic line feed still does not work or the spool is
jammed, try the following suggestions:
u Carefully clean the spool cover and housing.
u Remove the spool and check if the lever can move freely.
u Remove the spool and unwind the cutting line, then wind it
on neatly again as described above. Replace the spool as
instructed.
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker GL652 T3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker GL652 T3 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info