Manual Black Decker GL560PXC T5 (page 5 of 60) (English, German, Dutch, French, Italian, Portuguese, Spanish)

583265

Zoom out

Zoom in

1/60

Edging

Best results are achieved on edges greater

than 50mm deep.

Note: Your trimmer is a maintenance tool for

trimming overhanging grass and should not

be used to create edges. Edges can be

created using an edging spade.

With the skid (25) on the grass edge and the

edge guide (9) hooked over the edge, pull

the unit along while keeping the edge guide

in contact with the lawn edge.

A closer cut can be achieved by angling

the trimmer.

If your trimmer is suitable for use with a

‘Detachable’ extension cord, loop a length of

cord through the cord restraint (3) to avoid

the plug and socket coming apart

accidentally if the cord is pulled.

How to convert between the trimming

and edging mode (Fig. 3)

In addition to conventional trimming (Fig. D),

your trimmer can be used to trim

overhanging grass along lawn edges and

flower beds (Fig. J).

To convert your trimmer between the

trimming and edging mode:

Unlock

• With the trimmer switched off and the

edge guide (9) resting on the ground,

place one hand on the switch handle

(20). Using your other hand, turn the

locking ring (4) anti-clockwise, as far as

it will go (approximately quarter of a

turn) (Fig. 3.1).

Convert

• While keeping hold of the switch handle,

grasp the trimmer body (1) and rotate

half a turn in the direction of the arrow

(24), until the body ‘clicks’ into position

(Fig. 3.2).

Lock

• While still holding the switch handle,

tighten the locking ring clockwise, using

the other hand. Only light finger pressure

is required to secure it (Fig. 3.3).

Replacement line

A new spool containing 10 metres of cutting line

(cat. no. A6481) may be purchased from your

Black & Decker dealer. Alternatively, replacement

line packs are available.

For maximum reliability, never put on a heavier or

lighter line (e.g. fishing line) which will prevent the

automatic feed from functioning, cause motor

failure or reduce cutting performance.

How to fit a new spool of cutting line

(Fig. 4 & 5)

• Disconnect your trimmer from the power

supply.

• Remove the spool cover by pushing the

spool cover tabs (13) inwards and

upwards (Fig. 4), then pull off (it is not

necessary to push both tabs in at the

same time). The empty spool can now

be withdrawn from the drive shaft.

• Remove any dirt or grass that may have

collected inside the spool housing (12)

and cover (8).

• Unwind approximately 9cm (3.5") of

cutting line (5) from the new spool (17).

Feed the cutting line through the eyelet

and then push the spool onto the centre

drive shaft (Fig. 5). Rotate as necessary

to fully seat the spool, taking care not to

trap the cutting line underneath the spool

and making sure that there is a

minimum of 9cm (3.5") protruding from

the spool housing.

• Replace the spool cover by aligning

both tabs on it (13) with the slots in the

spool housing and pushing them into

place. Make sure that both tabs are

securely located.

How to wind new line onto an empty

spool (Fig. 6 & 7)

• A maximum of 10 metres of new cutting

line can be wound onto the empty spool.

The spool has an ‘Indicator’ to help you

avoid winding an excessive quantity of

cutting line on the spool, as too much will

prevent the automatic feed system from

functioning (Fig. 6).

• Remove any remnant of old cutting line

from the spool (17).

• Push the end of the new cutting line into

one of the two holes provided in the

spool (17) and insert 20mm.

ENGLISH

is there such a trimmer no GL565 has I cannot find it in your list of items I have got one. I did get spare parts for it but not sure how there Fit Thanks Phil Nunn. Submitted on 26-8-2023 at 18:29
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker GL560PXC T5 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,49 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker GL560PXC T5

Black Decker GL560PXC T5 Quick start guide - English - 16 pages

Black Decker GL560PXC T5 User Manual - Danish, Swedish, Norwegian, Finnish - 28 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker GL560PXC T5 Manual

Product: