527589

Black Decker GL4525 Manual

8
Zoom out
Zoom in
Previous page
1/100
Next page
8
ENGLISH
(Original instructions)
u If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
u Electric safety can be further improved by using a
highsensitivity 30 mA Residual Current Device (RCD).
Features
This appliance includes some or all of the following features.
1. On/off switch
2. Handle
3. Cable restraint
4. Power inlet
5. Second handle
6. Guard
7. Spool housing
8. Head
9. Edge guide
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting the guard (g. A-B)
u Remove the screw from the guard.
u Keeping the guard (6) square to the strimmer head (8)
slide it into place until the retaining tab clicks into place
(Ensure that the guide rails (10) on the guard (6) are
correctly aligned with the guide rails (11) on the strimmer
head (8). g. A).
u Secure the guard (6) with the screw (12).
Warning! Never use the tool unless the guard is properly
tted.
Attaching the second handle (g. C) (GL4525 &
GL5028 only)
u Slide the second handle (5) on to the main handle (2) in
an upwards direction.
u Secure the second handle in place with the screw (13)
provided.
Attaching the second handle (g. D) (GL5530 only)
u Press in and hold both of the buttons (14) on the side of
the handle.
u Slide the second handle (5) in place over the buttons (14).
Warning! Ensure that the teeth on the button are correctly
aligned in slots in the handle and that the handle is secure.
Adjusting the position of the secondary handle (g.
E) (GL5530 only)
The second handle (5) can be adjusted to provide optimum
balance and comfort.
u Press in the button (15) on the left side od the handle.
u Rotate the second handle (5) into the required position.
u Release the button (15).
Warning! Ensure that the teeth on the button are correctly
aligned in slots in the handle and that the handle is secure.
Adjusting the height of the tool (g. F)
This tool has a telescopic mechanism, allowing you to set it to
a comfortable height. There are multiple height settings.
To adjust the height setting, proceed as follows:
u Disconnect the tool from the supply.
u Loosen the adjustment collar (16) by turning it clockwise.
u Gently pull the tube (17) in or out of the handle (2) to the
desired height.
u Tighten the adjustment collar (16) by turning anti-
clockwise.
Releasing the cutting line
In transit, the cutting line is taped to the spool housing.
u Remove the tape holding the cutting line to the spool
housing (7).
Connecting the tool to the mains (g. G)
u Connect the female plug of a suitable extension cable to
the power inlet (4).
u Loop the cable through the cable restraint (3).
u Insert the mains plug into a mains outlet.
For wired in cable units: Make sure the cable is looped
through the cable restraint prior to connecting the plug to the
mains outlet.
Warning! The extension cable must be suitable for outdoor
use.
Use
Warning! Let the tool work at its own pace. Do not overload.
Setting the tool to trimming or edging mode (g. H,
I & J)
The tool can be used in trimming mode as shown in g. E or in
edging mode to trim overhanging grass along lawn edges and
ower beds as shown in g. F.
Trimming mode (g. H)
For trimming, the trimmer head should be in the position
shown in g. H. If it is not:
u Disconnect the tool from the supply.
u Loosen the adjustment collar (6) by turning it clockwise.
u Whilst holding the handle (2), rotate the head (8)
clockwise.
u Tighten the collar (6) by turning it anti-clockwise.
u Slide the edge guide (9) into the motor housing.
Note: Note: The head will only rotate in one direction.
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker GL4525 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker GL4525 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 6,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info