527583

Black Decker GL340 Manual

11
Zoom out
Zoom in
Previous page
1/16
Next page
7
ENGLISH
B2
Do not cut wet grass, best results are
achieved when the grass is dry.
B3
Cut at an angle and with the tip of the nylon
line. Your trimmer is balanced to operate at
this angle.
B4
Swing your trimmer gently from side to side.
B5
Do not overload your trimmer. It operates
best at high speeds.
B6
On long grass, start at the top.
B7
Take small cuts.
B8
If your trimmer features a cord restraint,
loop a length of cord through the restraint to
prevent the plug and socket coming apart
accidentally if the cord is pulled.
How to fit a new spool of cutting line
(Fig. F & G)
• Disconnect your trimmer from the
power supply.
F
• Remove the spool cover by pushing the
two spool cover tabs (12) inwards and
upwards (Fig. F), then pull off (it is not
necessary to push both tabs in at the
same time). The empty spool can now
be withdrawn from the drive shaft.
• Remove any dirt or grass that may have
collected inside the spool housing and
cover.
• Unwind approximately 9cm (3.5") of
cutting line (5) from the new spool (15)
and temporarily park the cutting line end
in one of the ‘L’ shaped slots to prevent
the line unravelling.
G
• Feed the cutting line through the eyelet
(14) and then push the spool onto the
centre drive shaft while pulling the free
end of the line to release it from the ‘L’
shaped slot. To fully seat the spool,
rotate as necessary, taking care not to
trap the cutting line underneath the spool
and making sure that there is a minimum
of 9cm (3.5") protruding from the
spool housing.
• Replace the spool cover by aligning
both tabs on it (12) with the slots in the
spool housing and pushing them into
place. Make sure that both tabs are
securely located.
How to wind new line onto an empty
spool (Fig. H & J)
H
• A maximum of 10 metres of new cutting
line can be wound onto the empty spool.
The spool has an ‘Indicator’ to help you
avoid winding an excessive quantity of
cutting line on the spool, as too much will
prevent the automatic feed system from
functioning.
• Remove any remnant of old cutting line
from the spool (15).
J1
• Push the end of the new cutting line into
one of the two retaining holes (17) provided
in the spool (15) and insert 20mm.
• Bend the cutting line over, pulling it
through the adjacent ‘L’ shaped slot.
The cutting line should now be firmly
anchored to the spool and you may
proceed to wind it on in the direction of
the arrow (16).
J2
• Take time to wind the cutting line on
neatly, in layers. Do not criss cross.
• When you have wound on sufficient
cutting line, temporarily park it in one of
the ‘L’ shaped slots to prevent the spool
unravelling, ensuring you leave a
minimum of 9cm (3.5") protruding.
• Fit the spool and spool cover (8) to the
spool housing as described for fitting a
new spool.
Replacement line
A new spool containing 10 metres of nylon line may
be purchased from your Black & Decker agent.
Alternatively, replacement packs containing 25 to
50 metres of line are available.
For maximum reliability never put on a heavier or
lighter line (eg. fishing line) which will prevent the
automatic feed from functioning, cause motor failure
or reduce cutting performance.
Care and maintenance
• For the best performance, please keep the nylon
line, spool and air slots in your trimmer body
clean. Use a dry brush or cloth to remove grass,
sap or other dirt.
• Plastic parts may be cleaned by using a mild
soap and a cloth dampened with hot water.
Do not use any other type of detergent, cleaner
GL340 UK p02-11 w/p 24/3/00, 2:17 pm7
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker GL340 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker GL340 in the language / languages: English as an attachment in your email.

The manual is 0,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info