527582
8
Zoom out
Zoom in
Previous page
1/84
Next page
8
Fitting a new spool of cutting line (fig. H - J)
Spool with single cutting line (fig. H)
Replacement spools of cutting line are available from your
Black & Decker dealer (cat. no. A6481).
Keep the tabs (16) depressed and remove the spool cover
(17) from the housing (12).
Remove the empty spool (18) from the spool housing.
Remove any dirt and grass from the spool cover and
housing.
Take the new spool and unwind approximately 9 cm of
cutting line.
Feed the cutting line through the eyelet (19).
Push the spool onto the drive shaft (20) and rotate it
slightly until it is seated. Make sure that the cutting line
is not trapped under the spool and that 9 cm of cutting
line protrudes from the housing.
Align the tabs on the spool cover with the holes in the
housing.
Push the cover onto the housing until it snaps securely
into place.
Warning! If the cutting line protrudes beyond the trimming
blade (10), cut it off so that they just reach the blade.
Spool with twin cutting line (fig. I & J)
Replacement spools of cutting line are available from your
Black & Decker dealer (cat. no. A6441). Complete cassettes
containing a spool of cutting line are also available (cat. no. A6488).
Keep the tabs (21) depressed and remove the spool cover
(22) from the housing (12).
Remove the empty spool (23) from the spool cover.
Remove any dirt and grass from the spool cover and
housing.
Take the new spool and push it onto the boss in the spool
cover. Rotate the spool slightly until it is seated.
Unclip the end of one of the cutting lines and feed the line
into one of the eyelets (24). The line should protrude
approximately 9 cm from the spool cover.
Unclip the end of the other cutting line and feed the line
into the other eyelet. The line should protrude
approximately 9 cm from the spool cover.
Align the tabs (21) on the spool cover with the cut-outs
(25) in the housing.
Push the cover onto the housing until it snaps securely
into place.
Warning! If the cutting lines protrude beyond the trimming
blade (10), cut them off so that they just reach the blade.
Winding a new cutting line onto an empty spool (fig. K - O)
You may wind new cutting line onto an empty spool.
Spool with single cutting line (fig. K & L)
Replacement packs of cutting line are available from your
Black & Decker dealer (cat. no. A6170 (25 m) & A6171 (40 m)).
Remove the empty spool from the tool as described
above.
Remove any remaining cutting line from the spool.
Feed 2 cm of cutting line into one of the holes (26) in the
spool as shown.
Bend the cutting line and anchor it in the L-shaped slot (27).
Wind the cutting line onto the spool in the direction of the
arrow (28). Make sure to wind the line on neatly and in
layers. Do not criss-cross.
When the wound cutting line reaches the recesses (29),
cut the line. Let the line protrude approximately 9 cm from
the spool and hold a finger on the line to keep it in place.
Proceed as described above to fit the spool on the tool.
Warning! Only use the appropriate type of Black & Decker
cutting line.
Spool with twin cutting line (fig. M - O)
Replacement packs of cutting line are available from your
Black & Decker dealer (cat. no. A6440).
Remove the empty spool from the tool as described
above.
Remove any remaining cutting line from the spool.
First wind new line onto the uppermost part of the spool:
Feed 2 cm of cutting line into one of the slots (30) in the
upper section of the spool as shown.
Wind the cutting line onto the spool in the direction of
the arrow (31). Make sure to wind the line on neatly
and in layers. Do not criss-cross.
When the wound cutting line reaches the recesses (32),
cut the line.
Temporarily park the line in the slots (33) on one side of
the spool as shown.
Repeat the above procedure for the second cutting line on
the lower section of the spool. Park the line in the unused
slots (33).
Proceed as described above to fit the spool on the tool.
Do not forget to release the cutting line from the parking
slots (33).
Warning! Only use the appropriate type of Black & Decker
cutting line. Ensure that cutting line is present in both sections
of the spool.
ENGLISH
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker GL337SB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker GL337SB in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info