527588
9
Zoom out
Zoom in
Previous page
1/64
Next page
9
ENGLISH
If the tool starts running slowly, reduce the load.
In order to achieve optimum cutting results,
only cut dry grass.
MAINTENANCE
Your Black & Decker tool has been designed to
operate over a long period of time with a
minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and
regular cleaning.
Before performing any maintenance,
switch off and unplug the tool.
Regularly clean the ventilation slots in your tool
using a soft brush or dry cloth.
Regularly clean the cutting line and spool
using a soft brush or dry cloth.
Regularly use a blunt scraper to remove grass
and dirt from the underneath of the guard.
Do not use any abrasive or solvent-based
cleaner.
Fitting a new spool of cutting line (fig. D)
Replacement spools of cutting line are available
from your Black & Decker dealer (cat. no. A6481).
Unplug the tool.
Keep the tabs (11) depressed and remove the
spool cover (12) from the housing (7).
Remove the empty spool (13) from the housing.
Remove any dirt and grass from the housing.
Take the new spool and unwind approx.
9 cm of cutting line.
Feed the cutting line through the eyelet (14).
Push the spool onto the drive shaft (15) and
rotate it slightly until it is seated. Make sure
that the cutting line is not trapped under the
spool and that 9 cm of cutting line protrudes
from the housing.
Align the tabs on the spool cover with the
holes in the housing.
Push the cover onto the housing until it snaps
securely into place.
If the cutting line protrudes beyond the
trimming blade (6), cut it off so that it just
reaches the blade.
Winding new line onto an empty spool (fig. E)
You may wind new cutting line onto an empty
spool. Replacement packs of cutting line are
available from your Black & Decker dealer
(cat. no. A6170 (25 m), A6171 (40 m)).
Remove the empty spool from the tool as
described above.
Remove any old cutting line from the spool.
Feed 2 cm of cutting line into one of the holes
(16) in the spool as shown.
Bend the cutting line and anchor it in the
L-shaped slot (17).
Wind the cutting line onto the spool in the
direction of the arrow (18). Make sure to wind
the line on neatly and in layers.
Do not criss-cross.
When the wound cutting line reaches the
recesses (19), cut the line. Let the line protrude
approx. 9 cm from the spool and hold a finger
on the line to keep it in place.
Proceed as described above to fit the spool on
the tool.
Only use round 1.5 mm diameter
Black & Decker cutting line. Do not use
Reflex Plus twisted cutting line. The use of
an incorrect type of cutting line can damage
the auto feed mechanism and will void the
warranty.
TROUBLESHOOTING
If your tool seems not to operate properly,
follow the instructions below. If this does not solve
the problem, please contact your local
Black & Decker repair agent.
Before proceeding, unplug the tool.
Tool does not start
Check that the power cables are properly
connected.
Check the mains fuses.
Tool vibrates strongly
Carefully clean the spool housing.
If this does not solve the problem, unwind the
line from the spool and rewind it more tightly.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker GL30 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker GL30 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info