527573

Black Decker GL250 Manual

6
Zoom out
Zoom in
Previous page
1/80
Next page
6
ENGLISH
(Original instructions)
Features
This appliance includes some or all of the following features.
1. On/off switch
2. Handle
3. Cable restraint
4. Power inlet
5. Second handle
6. Guard
7. Line trimming blade
8. Cutting line
9. Spool housing
10. Head
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Attaching the second handle (g. A) (GL310 &
GL360 only)
u Slide the second handle (5) on to the main handle (2) in
an upwards direction.
u Secure the second handle in place with the two screws
provided.
Fitting the guard (g. B)
u Place the guard onto the tool as shown.
u Firmly press the guard (6) until it snaps into place.
u Secure the guard with the screw.
Warning! Never use the tool unless the guard is properly
tted.
Releasing the cutting line
In transit, the cutting line is taped to the spool housing.
u Remove the tape holding the cutting line (8) to the spool
housing (9).
Connecting the tool to the mains (g. C)
u Connect the female plug of a suitable extension cable to
the power inlet (4).
u Loop the cable through the cable restraint (3).
u Insert the mains plug into a mains outlet.
For wired in cable units: Make sure the cable is looped
through the cable restraint prior to connecting the plug to the
mains outlet.
Warning! The extension cable must be suitable for outdoor
use.
Use
Warning! Let the tool work at its own pace. Do not overload.
Switching on and off
u To switch the tool on, squeeze the trigger lever (1).
u To switch the tool off, release the trigger lever.
Warning! Never attempt to lock the trigger lever in the on
position.
Hints for optimum use
General
u In order to achieve optimum cutting results, only cut dry
grass.
Trimming
u Hold the tool as shown in g. D.
u Gently swing the trimmer from side to side.
u When cutting long grass, work in stages from the top. Take
small cuts.
u Keep the tool away from hard objects and delicate plants.
u Cutting line will wear faster and require more feeding if the
cutting is done along pavements or other abrasive
surfaces or heavier weeds are being cut.
u As you use the trimmer, the string will get shorter due to
wear. Gently bump the unit on the ground whilst running
and the line will feed.
u If the tool starts running slowly, reduce the load.
Fitting a new spool of cutting line (g. E - F)
Replacement spools of cutting line are available from your
Black & Decker dealer (cat. no. A6226).
u Keep the tabs (12) depressed and remove the spool cover
(13) from the housing (9).
u Remove the empty spool (14) from the spool housing.
u Remove any dirt and grass from the spool cover and
housing.
u Take the new spool and unwind approximately 10 cm of
cutting line.
u Feed the cutting line through the eyelet (15).
u Push the spool onto the drive shaft (16) and rotate it
slightly until it is seated. Make sure that the cutting line is
not trapped under the spool and that 10 cm of cutting line
protrudes from the housing.
u Align the tabs (12) on the spool cover with the holes in the
housing (15).
u Push the cover onto the housing until it snaps securely
into place.
Warning! If the cutting line protrudes beyond the trimming
blade (7), cut it off so that it just reaches the blade.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker GL250 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker GL250 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info