585827
10
Zoom out
Zoom in
Previous page
1/140
Next page
10
Assembly
Warning! Before assembly, remove the battery (10) from the
tool.
Fitting and removing the battery (fig. A)
To fit the battery (10), line it up with the receptacle on
the tool. Slide the battery (10) into the receptacle and
push until the battery (10) snaps into place.
To remove the battery (10), push the release button (24)
while at the same time pulling the battery (10) out of the
receptacle.
Warning! To prevent accidental operation, make sure that
the battery is removed and that the chain sheath (11) is in
place on
the saw chain (8) before performing the following
operations. Failure to do this could result in serious personal
injury.
Installing and removing the saw chain (fig. C, E & G)
Place the tool on a firm and stable surface.
Loosen the two Allen screws (14) using the Allen key
(21) provided. Remove the Allen screws (14).
Remove the chain cover assembly (6).
Turn the chain tension adjustment screw (7) counter
clockwise to allow the guide bar (9) to recede and to
reduce the tension on the saw chain (8).
Remove the old saw chain (8) from the sprocket (15)
and the guide bar (9).
Place the new saw chain (8) in the groove of the guide
bar (9) and around the sprocket (15). Make sure that the
teeth are facing the correct direction by matching the
arrow on the saw chain (8) with the arrow on the chain
cover assembly (6).
Make sure that the slot (17) in the guide bar (9) is over
the location pins (18) and that the hole (20) below the
slot is located over the adjustment pin (19).
Fit the chain cover assembly (6) and the 2 Allen screws
(14).
Tighten the Allen screws (14) using the Allen key (21)
provided.
Always wear protective gloves when installing or
removing the saw chain (8). The saw chain is
sharp and can cut you when it is not running.
easily done before. The battery may become warm while
charging; this is normal and does not indicate a problem.
Warning! Do not charge the battery at ambient temperatures
below 10 °C or above 40 °C. Recommended charging
temperature: approx. 24 °C.
Note: The charger will not charge a battery if the cell
temperature is below approximately 10 °C or above 40 °C.
The battery should be left in the charger and the charger
will begin to charge automatically when the cell
temperature warms up or cools down.
To charge the battery (10), insert it into the charger (12).
force. Be sure that the battery is fully seated in the
charger.
Plug in the charger and switch on at the mains.
The charging indicator (23) will blink.
The charge is complete when the charging indicator (23)
switches to continuously on. The charger and the battery can
charger occasionally tops up the battery charge.
Charge discharged batteries within 1 week. Battery life will
be greatly diminished if stored in a discharged state.
Leaving the battery in the charger
The charger and battery pack can be left connected with the
pack fresh and fully charged.
Adjust the chain tension as described below.
ENGLISH
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker GKC1820L H1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker GKC1820L H1 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 6,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker GKC1820L H1

Black Decker GKC1820L H1 Quick start guide - English - 16 pages

Black Decker GKC1820L H1 User Manual - Polish - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info