585811
10
Zoom out
Zoom in
Previous page
1/16
Next page
10
The battery (10) will be fully charged in approximately 8
hours. It can be removed at any time or left in the connected
charger indefinitely.
1 hour charger (fig. C)
To charge the battery (10), remove it from the tool and
insert it into the charger (23). The battery (10) will only
fit into the charger (23) in one way. Do not force. Be sure
that the battery (10) is fully seated in the charger (23).
Plug in the charger (23).
Check that the red charging indicator comes on. If the
green ‘end of charge’ indicator comes on then the
battery is too hot and cannot be charged. If this
happens, remove the battery (10) from the charger (23),
let the battery cool down for approximately 1 hour and
re-insert it.
After approximately 1 hour of charging, the red charging
indicator will go off and the green ‘end of charge’ indicator
will come on. The battery is now fully charged.
Remove the battery (10) from the charger (23).
Installing and removing the saw chain (fig. D - F & H)
Always wear protective gloves when installing or
removing the saw chain (8). The saw chain (8) is
sharp and can cut you when it is not running.
Place the tool on a firm and stable surface.
Loosen the 2 Allen screws (14) using the Allen key (21)
provided. Remove the Allen screws (14).
Remove the chain cover assembly (6).
Turn the chain tension adjustment screw (7) counter
clockwise to allow the guide bar (9) to recede and to
reduce the tension on the saw chain (8).
Remove the old saw chain (8) from the sprocket (15)
and the guide bar (9).
Place the new saw chain (8) in the groove of the guide
bar (9) and around the sprocket (15). Make sure that the
teeth are facing the correct direction by matching the
arrow on the saw chain (8) with the arrow on the chain
cover assembly (6).
Make sure that the slot (17) in the guide bar (9) is over
the location pins (18) and that the hole (20) below the
slot is located over the adjustment pin (19).
Fit the chain cover assembly (6) and the 2 Allen screws
(14).
Tighten the Allen screws (14) using the Allen key (21)
provided.
Adjust the chain tension as described below.
Checking and adjusting the chain tension (fig. D and G)
Check the saw chain tension. The tension is correct
when the saw chain (8) snaps back after being pulled
away 3 mm from the guide bar (9) with light force from
the middle finger and thumb. There should be no ‘sag’
between the guide bar (9) and the saw chain (8) on the
underside.
To adjust the tension:
Loosen the 2 Allen screws (14).
Turn the chain tension adjustment screw (7) clockwise.
Warning! Do not over-tension the chain as this will lead to
excessive wear and will reduce the life of the bar and chain.
Once the chain tension is correct, tighten the 2 Allen
screws (14).
Warning! When the saw chain is new, check the tension
frequently during the first two hours of use as a new saw
chain stretches slightly.
Filling the oil reservoir (fig. H)
Remove the oil cap (3) and fill the reservoir (4) with the
recommended chain oil. You can see the oil level in the
oil reservoir (4). Refit the oil cap (3).
Periodically switch off and check the oil level; if it is less
than a quarter full, remove the battery (10) from the tool
and refill the reservoir (4) with the correct oil.
Oiling the chain (fig. H)
The saw chain (8) must be oiled before each use and after
cleaning using only the correct grade of oil (cat. no. A6027).
Lubricate the saw chain (8) by pressing the bulb on the
oil cap (3) twice before making each cut, holding the
bulb down for 3-4 seconds.
Residual risks
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks cannot be avoided. These include:
Injuries caused by touching any rotating/moving parts.
Injuries caused when changing any parts, blades or
accessories.
Injuries caused by prolonged use of a tool. When using
any tool for prolonged periods make sure you take
regular breaks.
Impairment of hearing.
Health hazards caused by breathing dust developed
when using your tool (example:- working with wood,
especially oak, beech and MDF).
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker GKC1817 H1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker GKC1817 H1 in the language / languages: English as an attachment in your email.

The manual is 1,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker GKC1817 H1

Black Decker GKC1817 H1 User Manual - English, German, Dutch, Danish, French, Italian - 136 pages

Black Decker GKC1817 H1 User Manual - Polish - 16 pages

Black Decker GKC1817 H1 User Manual - Portuguese, Swedish - 136 pages

Black Decker GKC1817 H1 User Manual - Turkish - 12 pages

Black Decker GKC1817 H1 User Manual - Spanish, Spanish, Norwegian, Finnish - 136 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info