78522
9
Zoom out
Zoom in
Previous page
1/136
Next page
9
ENGLISH
Do not probe the charger.
The appliance/tool/battery must be placed in a well
ventilated area when charging.
Labels on the charger
The following symbols are found on your charger:
Electrical safety
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Warning! Never attempt to replace the charger unit with a
regular mains plug.
Features
1. On/off switch
2. Lock-off button
3. Oil cap
4. Oil reservoir
5. Front guard assembly
6. Chain cover assembly
7. Chain tension adjustment screw
8. Chain
9. Guide bar
10. Battery
11. Chain sheath
12. Charger receptacle
13. Charger
Assembly
Warning! Before assembly, remove the battery (10) from
the tool.
Fitting and removing the battery (fig. A)
To fit the battery (10), line it up with the receptacle on
the tool. Slide the battery (10) into the receptacle and
push until the battery (10) snaps into place.
To remove the battery (10), push the release button (24)
while at the same time pulling the battery (10) out of the
receptacle.
Warning! To prevent accidental operation, make sure that
the battery is removed and that the chain sheath (11) is in
place on the saw chain (8) before performing the following
operations. Failure to do this could result in serious personal
injury.
Charging the battery (fig. B and C)
The battery (10) needs to be charged before first use and
whenever it fails to produce sufficient power on jobs that
were easily done before. When charging the battery (10) for
the first time, or after prolonged storage, it will only accept an
80% charge.
After several charge and discharge cycles, the battery (10)
will attain full capacity. The battery (10) may become warm
while charging; this is normal and does not indicate a
problem.
Warning! Do not charge the battery at ambient
temperatures below 10°C or above 40°C. Recommended
charging temperature: approx. 24°C.
8 hour charger (fig. B)
To charge the battery (10), remove it from the tool and
slide the charger receptacle (12) onto the battery (10).
Plug in the charger (13).
Read the instruction manual before use.
The charger automatically shuts off if the ambient
temperature becomes too high. As a consequence
the charger will be inoperable. The charging base
must be disconnected from the mains supply and
taken to an authorised service centre for repair.
Charge only at ambient temperatures between
10°C and 40°C.
The charger is intended for indoor use only.
Your charger is double insulated; therefore no
earth wire is required. Always check that the power
supply corresponds to the voltage on the rating
plate.
Your charger is double insulated; therefore no earth
wire is required. Always check that the power
supply corresponds to the voltage on the rating
plate.
T1A
+40ºC
+10ºC
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker GKC 1817 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker GKC 1817 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info