584962
11
Zoom out
Zoom in
Previous page
1/124
Next page
11
ENGLISH
(Original instructions)
When supported at one end:
u First cut one third up to avoid splintering and second, cut
down to prevent splintering.
When on a slope (g. L):
u Always stand on the uphill side.
When attempting to cut a log on the ground (g. L):
u Secure the workpiece using chocks or wedges. The user
or a bystander should not steady the log by sitting or
standing on it. Make sure that the saw chain does not
contact the ground.
When using a saw horse (g. M):
This is strongly recommended whenever possible.
u Position the log in a stable position. Always cut on the
outside of the saw horse arms. Use clamps or straps to
secure the workpiece.
Troubleshooting
Problem Possible cause Possible
solution
Tool will not start Lock button not
pressed.
Press the lock
button.
Front guard in the
brake position
Reset front guard
Blown fuse Replace fuse
Tripped RCD Check RCD
Mains lead not
connected
Check mains
supply
Chain does not
stop instantly
when the tool is
switched off
Chain tension is
too slack
Check chain
tension
Bar/chain appear
hot/smoking
Oil tank empty Check oil tank
level
Oil hole blocked
on chain bar
Clean oil hole
Chain tension is
too tight
Check chain
tension
Guide bar
sprocket
nose needs
greasing
Oil the guide bar
sprocket nose
Problem Possible cause Possible
solution
Chainsaw does
not cut well
Chain on
backwards
Check/modify
chain direction
Sharpen
Chainsaw not
using oil
Debris in tank Empty oil from
tank and replace
Oil hole in cap
blocked
Remove debris
from hole
Debris in chain
bar
Remove debris
and clean the
chain bar
Debris in oil outlet remove debris
Maintenance
Regular maintenance ensures a long effective life for the
tool. We recommend you make the following checks on a
regular basis.
Warning! Before performing any maintenance on power tools:
u Switch off and disconnect the tool from the mains supply.
Oil level
The level in the reservoir should not be allowed to fall below
a quarter full.
Saw chain and guide bar (g. G)
u After every few hours of use and before storage, remove
the guide bar (7) and the saw chain (6) and clean them
thoroughly.
u Make sure that the guard is clean and free from debris.
u On reassembling, turn the guide bar (7) through 180° and
oil sprocket nose via the sprocket lubrication hole (16).
This ensures an even distribution of wear around the
guide bar rails.
Saw chain sharpening
If you are to get the best possible performance from the tool
it is important to keep the teeth of the saw chain sharp.
Guidance for this procedure is found on the sharpener
package. For this purpose we recommend the purchase of
the Black & Decker saw chain sharpening kit (available from
Black & Decker service agents and selected dealers).
Replacing worn out saw chains
Replacement saw chains are available through retailers or
Black & Decker service agents. Always use genuine spare
parts.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker GK2240 T3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker GK2240 T3 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info