Manual Black Decker GK2240 T3 (page 7 of 124) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

584962

Zoom out

Zoom in

1/124

ENGLISH

(Original instructions)

u Do not overreach and do not cut above shoulder

height. This helps prevent unintended tip contact and

enables better control of the chainsaw in unexpected

situations.

u Only use replacement guide bars and chains

specified by the manufacturer. Incorrect replacement

guide bars and chains may cause chain breakage and/

or kickback.

u Follow the manufacturer's sharpening and

maintenance instructions for the saw chain.

Decreasing the depth gauge height can lead to

increased kickback.

u Striking metal, cement or any other hard material near

the wood, or buried in the wood can cause kickback.

u A dull or loose chain can cause kickback.

u Do not try to insert into a previous cut. As this could

cause kickback. Make a fresh cut every time.

Safety recommendations for the chainsaw

u We strongly recommend that first time users obtain

practical instruction in the use of the chainsaw and

protective equipment from an experienced user. Initial

practice should be completed sawing logs on a saw

horse or cradle.

u Always check that the kickback brake operates correctly

before use.

u We recommend that when carrying the chainsaw that

you make sure that the brake is engaged and the saw

chain is facing backwards.

u Maintain your chainsaw when not in use. Do not store

your chainsaw for any length of time without first

removing the saw chain and guide bar which should be

kept immersed in oil. Store all parts of your chainsaw in

a dry, secure place out of reach of children.

u We recommend you drain the oil reservoir prior to

storage.

u Be sure of your footing and pre-plan a safe exit from a

falling tree or branches.

u Use wedges to help control felling and prevent binding

the guide bar and saw chain in the cut.

u Saw chain care. Keep the saw chain sharp and snug on

the guide bar. Ensure the saw chain and guide bar are

clean and well oiled. Keep handles dry, clean and free

from oil and grease.

Avoid cutting

u Prepared timber.

u Into the ground.

u Into wire fences, nails. etc.

Vibration

The declared vibration emission values stated in the technical

data and the declaration of conformity have been measured in

accordance with a standard test method provided by

EN 60745 and may be used for comparing one tool with

another. The declared vibration emission value may also be

used in a preliminary assessment of exposure.

Warning! The vibration emission value during actual use of

the power tool can differ from the declared value depending

on the ways in which the tool is used. The vibration level may

increase above the level stated.

When assessing vibration exposure to determine safety

measures required by 2002/44/EC to protect persons regularly

using power tools in employment, an estimation of vibration

exposure should consider, the actual conditions of use and the

way the tool is used, including taking account of all parts of

the operating cycle such as the times when the tool is

switched off and when it is running idle in addition to the

trigger time.

Electrical safety

This tool is double insulated; therefore no earth wire

is required. Always check that the power supply

corresponds to the voltage on the rating plate.

u If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Black & Decker Service

Centre in order to avoid a hazard.

Using an extension cable

u Always use an approved extension cable suitable for the

power input of this tool (see technical data). The extension

cable must be suitable for outdoor use and marked

accordingly. Up to 30 m of HO7RN-F 2 X 1.5 mm²

extension cable can be used without loss of product

performance. Before use, inspect the extension cable for

signs of damage, wear and ageing. Replace the extension

cable if damaged or defective. When using a cable reel,

always unwind the cable completely.

Voltage drops

u Under certain power supply conditions this product may

cause short-time voltage drops during start-up.

u Other equipment may be affected. For example, electric

lights may temporarily reduce in brightness.

u Contact the supply authority, if necessary, to determine

that the impedance of the power supply is lower than

0.411 ohms. Disturbances are unlikely to occur under this

condition.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker GK2240 T3 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,97 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker GK2240 T3 Manual

Product: