55630
11
Zoom out
Zoom in
Previous page
1/108
Next page
11
ENGLISH
Fit the chain cover bolt (7) and tighten it finger
tight.
Turn the screw (14) (fig. D) clockwise until the
chain is tight. Make sure that the chain is snug
around the guide bar. Do not overtighten.
Tighten the chain cover bolt using the spanner
supplied.
Checking and adjusting the chain tension (fig. D)
Before use and after every 10 minutes of use,
you must check the chain tension.
Lightly pull on the chain as shown. The tension
is correct when the chain snaps back after
being pulled 3 mm away from the guide bar.
There should be no “sag” between the guide
bar and chain on the underside.
Note: Do not over-tension the chain as this will
lead to excessive wear and will reduce the life of
the bar and chain.
Note: When the chain is new, check the tension
frequently (after disconnecting from the mains)
during the first 2 hours of use as a new chain
stretches slightly.
To increase the tension:
Turn the screw (14) clockwise.
USE
Let the tool work at its own pace. Do not
overload.
Filling oil into the reservoir (fig. E)
Remove the oil cap (3) and fill the reservoir with
the recommended chain oil. You can see the oil
level in the indicator slot (4). Refit the oil cap.
Periodically switch off and check the oil in the
indicator; if it is less than a quarter full,
disconnect your chainsaw from the mains and
refill with the correct oil.
Auto-stop chainbrake (fig. F & G)
This tool is fitted with an auto-stop chainbrake which
will stop the chain within 150 ms each time you
release the rear trigger, or if kickback should occur.
This brake should be tested before every use.
How to set the chainbrake
Make sure that the tool is disconnected from
the mains supply.
Pull the front guard (5) back into the “set”
position .
The tool is now ready to use.
How the anti-kickback chainbrake works
In the event of kickback, your left hand comes in
contact with the front guard, pushing it backwards,
and stops the tool within 150 ms.
How the inertia activated chainbrake works
The chainbrake is activated when the front hand
guard is pushed forward, either manually, by the
back of the users hand or by its own weight. The
advantage of the inertia brake is that it is activated
by a severe kickback, eg. when the chain hits metal,
even if the users hand does not contact the front
guard, ie. when the saw is in the felling position.
How to test the anti-kickback chainbrake
Grip the tool firmly in both hands on a firm
surface - make sure the chain is clear of the
ground and switch on (see “How to switch your
chainsaw on”).
Rotate your left hand forward around the front
handle so that the back of your hand comes in
contact with the front guard and pushes it
backwards (fig. G). The chain should stop
within a few fractions of a second.
To reset after the operation of the chainbrake
Follow the instructions for setting the
chainbrake.
Notes:
It will not be possible to switch the tool on if
the front guard is not in the “set” position.
Avoid re-starting the tool until you hear the
motor come to a complete rest.
If the chain does not come to rest immediately
then this indicates that it needs tensioning (see
“Fitting the guide bar and chain”).
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker GK1630 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker GK1630 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info