584938
12
Zoom out
Zoom in
Previous page
1/20
Next page
12
ENGLISH
The extension cable contains two wires, which are
colour coded for easy identification: brown is for
Live (L), blue is for Neutral (N). The connector is
marked ‘L’ for Live and ‘N’ for Neutral.
These markings are located inside the body near
the terminal screws (see below).
Lift out the cable protector.
Pass the cable through from the narrow end of
the cable protector.
Prepare the cable ends to the strip length
shown in the illustration.
Remove the cable clamp.
Loosen the terminal screws until you can enter
the stripped wires between the raised washer
and the terminal.
Connect the brown lead to the terminal
marked ‘L’ and the blue lead to the terminal
marked ‘N’. Do not fix the wires directly under
the screw head.
Locate the cable and cable protector into the
body.
Fit the cable clamp over the outer sheath of
the cable. Tighten the screws until fully home.
Make sure that the cable clamp is firmly
holding the outer sheath of the cable and that
the two leads are correctly fixed.
Place the cover onto the connector body.
Securely tighten the fixing screw.
Check that the cable protector is secure and
that there are no gaps between the connector
body and the cover.
fixing screw
cover
terminal screws
clamping washers
connector body
cable
clamp
a
cable
protector
bc
6 mm
30 mm
Additional safety instructions for Australia and
New Zealand
This appliance is not intended for use by
young or infirm persons without supervision.
Children must be supervised to ensure they do
not play with the appliance.
If the supply cord is damaged, it must be
replaced by the manufacturer or an authorised
Black & Decker Service Centre in order to
avoid a hazard.
Technical data
Bar length 30 cm 35 cm 40 cm
Supply voltage (V) 230 230 230
Rated input (W) 1300/1400/ 1400/ 1400/
1600 1600 1600
Max. cutting length (cm) 30 35 40
Chain speed (no load m/s) 8 8 8
Weight (kg) 3.7 3.8 3.9
Oil capacity (ml) 180 180 180
Safety class II II II
OVERVIEW (fig. A)
1. On/off switch
2. Lock-off button
3. Oil cap
4. Oil level indicator
5. Front guard/chain brake
6. Chain cover
7. Chain cover bolt
8. Guide bar
9. Chain
10.Chain sheath
11.Spanner
ASSEMBLY
Before assembly, make sure that the tool
is switched off and unplugged.
Oiling the chain (fig. A)
You must do this whenever you use a new
chain for the first time. Take the new chain out
of its plastic bag and soak it in chain oil for at
least an hour before using it. Use Black & Decker
chain oil (cat. no. A6027).
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker GK1630 T4 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker GK1630 T4 in the language / languages: English as an attachment in your email.

The manual is 1,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker GK1630 T4

Black Decker GK1630 T4 User Manual - English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Spanish, Norwegian, Finnish - 108 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info