Manual Black Decker GK1435 (page 12 of 104) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Spanish, Norwegian, Finnish)

474483

Zoom out

Zoom in

1/104

ENGLISH

If the saw chain or bar becomes jammed:

◆ Switch the tool off.

◆ Disconnect the tool from the mains supply.

◆ Open the cut with wedges to relieve the strain

on the guide bar. Do not try to wrench the saw

free. Start a fresh cut.

Felling (fig. H - J)

◆ Pre-plan a safe exit from falling trees or branches.

◆ Cut one third of the diameter of the tree (Fig. H).

Then cut down from above to make a notch of

about 45°. This way you will avoid pinching the

saw.

◆ Make a single felling cut from the other side

but stop before you cut through to the notch

(fig. I).

◆ Drive a wedge or wedges into the felling cut to

open it and drop the tree (fig. J).

Logging (fig. K - M)

How you should cut depends on how the log is

supported. Use a saw horse whenever possible.

Always start a cut with the chain running and the

spiked bumper (15) in contact with the wood (fig. K).

To complete the cut use a pivoting action of the

spiked bumper against the wood.

When supported along its whole length

◆ Make a downward cut, but avoid cutting the

earth as this will blunt your saw quickly.

When supported at both ends

◆ First, cut one third down to avoid splintering

and second, cut again to meet the first cut.

When supported at one end

◆ First, cut one third up to avoid splintering and

second, cut down to prevent splintering.

When on a slope (fig. L)

◆ Always stand on the uphill side.

When using a saw horse (fig. M)

This is strongly recommended whenever possible.

◆ Position the log in a stable position. Always cut

on the outside of the saw horse arms.

MAINTENANCE (fig. N)

Regular maintenance ensures a long effective life

for the tool. We recommend you make the

following checks on a regular basis.

Oil level

The level in the reservoir should not be allowed to

fall below a quarter full. Top up if low.

Chain and guide bar

◆ After every few hours of use, remove the guide

bar and chain and clean thoroughly.

◆ On reassembling, the guide bar should be

turned through 180° and the sprocket nose

greased via the sprocket lubrication hole (18).

This ensures an even distribution of wear

around the guide bar rails.

TROUBLESHOOTING

If the tool does not operate correctly, check the following.

Fault Possible cause Action

Tool will not start. Blown fuse. Replace fuse.

Tripped RCD. Check RCD.

Mains lead not connected. Check mains supply.

Tool will not start - lock-off

button will not slide. Front guard in the brake position Reset front guard.

Chain does not stop instantly

when the tool is switched off. Chain tension is too slack. Check chain tension.

Bar/chain appear hot/smoking. Oil tank empty. Check oil tank level.

Chain tension is too tight. Check chain tension.

Guide bar sprocket nose needs greasing.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker GK1435 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,39 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker GK1435 Manual

Product: