527511
5
Zoom out
Zoom in
Previous page
1/52
Next page
5
Locate the cable and cable protector into the
body correctly (see opposite, figure a). Then fit
the cable clamp over the outer sheath of the
cable and screw down until the screws are fully
home. Failure to do this may result in the cover
not fitting correctly to the connector body.
Before replacing the cover of the ‘female’
connector make sure that the cable clamp is
holding the outer sheath of the cable firmly with
screws fully home and that the two leads are
correctly fixed at the terminal screws and are not
taut (see opposite, figure a).
Place the cover onto the body assembly
ensuring that it seats flat, then retighten the
fixing screw into the nut until the cover is
securely held (see opposite, figure c).
Finally check that the cable protector is secure
and that there are no gaps between the cover
and the connector body.
terminal screws
clamping washers
connector body fixing screw
6mm
cable
clamp cover
cable
protector
Fitting a new mains plug (UK only)
Fitting the ‘female’ connector
(UK only)
To remove the cover, unscrew the fixing screw until it
is free of the nut which is located in the hexagonal
recess on the underside of the connector.
Take care not to lose the nut if it falls out.
There is no need to completely remove the fixing
screw as it is intended to remain captive in the cover.
The cover can now be removed by applying
pressure as follows.
apply
pressure here
The extension cable contains two wires which are
colour coded for easy recognition; brown is for ‘Live’
(L) and blue is for ‘Neutral’ (N). The female connector
is marked ‘L’ for live and ‘N’ for neutral. These
markings are located inside the body near the
terminal screws (see opposite, figure a). With the
connector cover removed, lift out the cable protector
and proceed as follows:
Pass the cable through from the narrow end of
the cable protector (see opposite, figure a).
Prepare the cable ends to the specified strip
lengths (see opposite, figure b).
Remove cable clamp (see opposite, figure a).
Take care of loose parts.
To connect the extension cable to the connector
terminals, unscrew the terminal screws until the
clamp washers have lifted just enough to enter
the conductor between the raised washer and
the terminal (see below). Connect the brown
lead to ‘L’ and the blue lead to ‘N’. N.B. There is
no need to remove the terminal screws.
Connections are not to be made under the
screw heads.
terminal screw
clamp terminal
washer conductor position
to left of screw
ENGLISH
Fit a
BS1363A
approved
plug
Connect blue
to N (neutral)
Make sure that the
outer sheath of the
cable is held firmly
by the clamp
Fit the
recommended
fuse
Connect brown
to L (live)
240 volts AC only.
Never use a light
socket
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker GA100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker GA100 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info