529741

Black Decker FV1205N Manual

6
Zoom out
Zoom in
Previous page
1/64
Next page
6
ENGLISH
Installation
Attaching the handle to the appliance (fig. A)
X Align the D-handle with the main body of the unit and
push it down until it is fully seated.
X Remove the phillips head screw from the plastic bag.
X Insert the screw (13) into the hole.
X Tighten the screw (13) using a phillips screwdriver.
Charging base (fig. B)
Place the charging base (4) on the floor, convenient to an
electrical outlet. The Pivot Plus
®
slim vac is stored and
charged in the base whenever it is not in use.
Warning! Falling/tripping hazard. Do not place the charging
base on any elevated surface. The appliance is designed to
be placed into and removed from the charging base when
it is sitting on the floor convenient to an electrical outlet.
Use
Before first use, the battery must be charged for at least
16 hours.
X Place the appliance on the charging base (4) whenever
it is not in use.
You may need to charge the appliance many times initially in
order to achieve the best running time performance.
Charging the battery (fig. B)
Warning! Do not charge the battery at ambient
temperatures below 10°C or above 40°C.
X Make sure that the appliance is switched off.
The battery will not be charged with the beater bar/vac On/
Off switch (9) in the on position.
X Place the appliance on the charging base (4) as shown.
X Plug in the charger. Switch on at the mains.
The charging indicator (5) will be lit.
X For the first charging, leave the appliance to charge for
at least 16 hours.
While charging, the charger may become warm. This is
normal and does not indicate a problem.
The appliance can be left connected to the charger
indefinitely. The charging indicator (5) will be lit as long as
the appliance is connected to the plugged-in charger.
Opening the appliance (fig B, C and D)
X To open the appliance for use, lift it from the charging
base (4) (fig. B).
X Pull back the pivot lock trigger (1) on the handle and
rotate the vacuum head (fig. C).
X Release the pivot lock trigger (1) to lock the appliance
in any of the three different working positions a, b and c
(fig. D).
Switching on and off (fig. E)
X To switch the appliance on, slide the beater bar/vac On/
Off switch (9) forward to position 1 (vacuum only).
X For vacuuming with the beater bar operation, slide the
switch (9) forward to position 2.
X To switch the appliance off, slide the switch (9) back
to position 0.
Troubleshooting
If the product does not work, check the following:
X The charger was correctly plugged in for recharge
(it feels slightly warm to the touch).
X The charger cord is not damaged and is correctly
attached to the base.
X The charger is plugged into a working electrical outlet.
If the unit does not charge, check the following:
X Make sure that the beater bar/vac On/Off switch (9) is at
position 0. The appliance will not charge if the appliance
is switched ON.
Cleaning and maintenance
Warning! Regularly clean the filters.
Cleaning the dust container and filters (fig. F and G)
The filters are re-usable and should be cleaned regularly.
X Press the release latch (3) and open the container
door (2).
X Remove the filters (10 and 11).
X Empty the dust container.
X Brush any loose dust off the filters.
X Wash the filters in warm, soapy water (fig. G).
Warning! Do not immerse the appliance in water. A damp
cloth and soapy water should be used to clean the exterior
of the appliance. Always make sure that the appliance is
completely dry before re-use or storing.
X Make sure that the filters (10 and 11) are dry.
X Refit the filters (10 and 11).
X Close the container door (2). Make sure that the release
latch (3) clicks into place.
Warning! Never use the appliance without the filters.
Optimum dust collection will only be achieved with clean
filters.
Maintenance access (Fig. H and I)
The maintenance access panel (8) from the pivot arm (6) can
be removed to aid cleaning should the appliance become
blocked, resulting in a loss of suction.
X Remove the maintenance access panel (8) using a flat
bladed screwdriver (fig. I) to release the front clip
features.
X Once released, the section will pivot free of the main
assembly to give access for cleaning.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker FV1205N at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker FV1205N in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info