709570
5
Zoom out
Zoom in
Previous page
1/36
Next page
5
ENGLISH
(Original instructions)
Attaching the hose and accessories (Fig. A & B)
Warning! Inspect the seal (2a) on the steam nozzle (2) and
hose (3) before each use. If the seal is missing or damaged
then please contact your nearest authorised repair agent. Do
not use the appliance.
Attaching the hose (Fig. A)
u Press in the clips (3a) on either side of the hose (3).
u Press the hose (3) onto the steam nozzle (2) and release
the clips (3a).
Important! Ensure that the hose (3) is securely fastened
before using SteaMitt
TM
. If steam escapes from the joint then
the SteaMitt
TM
is not correctly tted, allow the unit to cool then
remove and re-t the hose.
Removing the hose and accessories (Fig. A & B)
Warning! The Steam nozzle, hose and SteaMitt
TM
become hot
during use.
Allow the unit and all attachments to cool before removing.
Removing the hose (Fig. A)
u Press in the clips (3a) on either side of the hose (3) and
pull away from the steam nozzle (2)
Filling the water tank (Fig. C)
Note! Fill the water tank with clean tap water. Donot use
chemicals or any other additives.
Note! In areas of very hard water, the use of de-ionised water
is recommended.
u Switch off the unit and disconnect from the mains supply.
u Open the ller cap (7) by ipping it up.
u Fill the water tank (6) with water.
Warning! Your water tank has a 0.10 litre capacity. Do not
over ll the tank.
u Replace the lter cap.
Note: Ensure the lter cap is rmly secured.
Note: Do not use chemical cleaners with your SteaMitt
TM
.
Fitting the cleaning pad (Fig. B)
u Fit the cleaning pad (9) to the SteaMitt
TM
(4) by attaching
the 'loop' velcro strips (9a) on the upper side of the
cleaning pad, to the 'hook' velcro pads (4a) on the
underside of the SteaMitt
TM
(4). Press down rmly.
Warning! The SteaMitt
TM
should not be used without tting a
cleaning pad.
Note: The SteaMitt
TM
accommodates 3 types of cleaning pads
of varying thickness. The thinnest can be used for cleaning 3D
forms such as taps etc. The thicker versions can be used for
larger at areas.
Use
Switching on and off
u To switch the appliance on, press the ON/Off button (5). It
takes approximately 15 seconds for the SteaMitt
TM
to heat
up.
Note: always have your hand inside the SteaMitt
TM
before you
press the steam button.
u To produce steam, press the steam button (1) on top of
the unit.
u To switch the appliance off, turn off the steam switch (1)
then press the ON/OFF button (5).
Caution! Always empty the SteaMitt
TM
water tank after use.
Note! When rst lled or after running dry, it can take up to 45
seconds for steam to be produced.
Hints for optimum use
General
u For optimal cleaning results never use the SteaMitt
TM
without rst attaching a cleaning pad.
u Do not use chemical cleaners or any other additives with
your SteaMitt
TM
.
u Delicate surfaces, mirrors for example, should be cleaned
first while the pad is at its driest, thereby avoiding streaks.
u Do not use the SteaMitt
TM
on cold glass, such as windows
as damage may be caused by the sudden change in
temperature.
Caution! It is important to monitor the water level in the water
tank (6). To rell the water tank and continue to sanitize/clean
turn the SteaMitt
TM
'OFF'. Unplug the unit from the electrical
wall outlet, rell the water tank (6).
@
Warning! Always use the SteaMitt
TM
as shown in figure
E, with your hand inside the protective glove.
@
Warning! Never attempt to use the SteaMitt
TM
by
gripping it externally as shown in figure F. This will result
in scalding.
@
Warning! Avoid using the SteaMitt
TM
in tight corners as
shown in gure H.
@
Warning! Should a problem occur during use, use the
quick release tab (8) to quickly remove the SteaMitt
TM
from your hand as shown in gure I.
After use (Fig. E)
u Turn the SteaMitt
TM
'OFF'. Turn the steam operation button
(1) to off and then press the ON/OFF button (5).
u Wait until the SteaMitt
TM
cools down.
u Unplug the SteaMitt
TM
from the electrical wall outlet.
u Empty the water tank.
u remove the cleaning pad (9) and wash it ready for next
use.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker FSH10SM at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker FSH10SM in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info