585913

Black Decker EMAX34 T2 Manual

3
Zoom out
Zoom in
Previous page
1/52
Next page
3
ENGLISH
(Original instructions)
u Move the lever towards the rear of the appliance to lower
the height of cut.
u Move the lever towards the front of the appliance to raise
the height of cut.
u Push the height adjustment lever (7) into one of the 6
height locations.
Note: The height of cut can be viewed on the height of cut
gauge (8) on the side of the unit.
Switching on and off (g. I)
Switching on
u Push in and hold the lock-off button (27).
u Pull the on/off switch (2) towards the handle.
u Release the lock-off button.
Switching off
u Release the on/off switch (2).
Warning: Never attempt to lock a switch in the on position.
Mowing (g. P1 & P2) (EMax38i, EMax42i &
EMax42ri only)
We recommend to use your mower as outlined in this section
in order to achieve optimum results and to reduce the risk of
cutting the mains cable.
u Loop the mains cable through the intelligent cable
management system (4) as shown (g. H) ensue that you
leave approximately 100 cm of cable between the switch-
box (1) and the intelligent cable management restraint (4).
u Ensure that the cable restraint can slide freely from one
handle to the other.
u Place the bulk of the mains cable on the lawn, close to the
starting point (position 1 in g. P1).
u Switch the appliance on as described above.
u Proceed as shown in g. P1
u Move from position 1 to position 2.
u Turn right, stepping over the cable and proceed towards
position 3. The cable restraint will slide from one side of
the handle to the other ensuring that the cable is laid out
away from the cutting blade.
u Turn left, stepping over the cable and move towards posi-
tion 4. The cable restraint will slide from one side of the
handle to the other ensuring that the cable is laid out away
from the cutting blade.
u Repeat the above procedure as required.
Warning: Do not work towards the cable as shown in g. P2.
Mowing (g. P1 & P2)(EMax34s & EMax34i only)
We recommend to use your mower as outlined in this section
in order to achieve optimum results and to reduce the risk of
cutting the mains cable.
u Place the bulk of the mains cable on the lawn, close to the
starting point (position 1 in g. P1).
u Switch the appliance on as described above.
u Proceed as shown in g. P1
u Move from position 1 to position 2.
u Turn right and proceed towards position 3.
u Turn left and move towards position 4.
u Repeat the above procedure as required.
Warning: Do not work towards the cable as shown in g. P2.
EdgeMax (g. K1 & K2)
EdgeMax allows you to cut grass right up to the edge of a wall
or fence (g K1).
EdgeMax allows you to accurately cut grass right up to the
edge of your lawn (g K2).
u With the lawnmower parallel with the edge of your lawn.
u Push the lawnmower along the edge of the lawn. Ensure
that the EdgeMax (9) is slightly over the edge of your lawn
(g.K2)
Compact&Go (g. J) (EMax34i, EMax38i, EMax42i &
EMax42ri only)
When the grass collection box is full you can compact the
grass in the collection box. You can determine how full the
grass collection box is by looking through the clear grass ap
(11).
u Release the on/off switch (2).
u Using your right foot, press the grass compaction lever
(29) all the way down until it locks into place.
Note: The grass in the collection box is now compressed into
the rear of the box. You may continue mowing until the grass
collection box becomes full.
Emptying the grass collection box (g. J) (EMax34i,
EMax38i, EMax42i & EMax42ri only)
u Release the on/off switch (2).
u Remove the grass collection box (10).
u Empty the contents from the front of the box.
u Place the grass collection box on the ground and pull in
and hold the grass compaction lever release button (30).
u Lift the grass compaction lever (29) into the vertical
position and release the grass compaction lever release
button (30).
u Empty the contents from the rear of the box.
Emptying the grass collection box (EMax34s only)
When the grass collection box is full you should empty the
grass in the collection box.
u Release the on/off switch (2).
u Remove the grass collection box (10).
u Empty the contents from the box.
3 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker EMAX34 T2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker EMAX34 T2 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker EMAX34 T2

Black Decker EMAX34 T2 Quick start guide - English - 8 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info