579640
8
Zoom out
Zoom in
Previous page
1/12
Next page
8
ENGLISH
(Original instructions)
Maximum cutting capacity
Note: Capacity shown on chart assumes no wheel wear and
optimum fence position.
Workpiece
shape
90
O
cutting
angle
A = 4-7/8"
(125mm)
A = 4-1/2"
(115mm)
4-1/2" x 5-1/8"
(115mm x 130mm)
4" x 7-5/8"
(115mm x 130mm)
3" x 7-3/8"
(115mm x 130mm)
A = 4-1/2" x 5-3/8"
(115mm x 137mm)
45
O
Cutting
Angle
A= 4-1/2"
(115mm)
A = 3-13/16"
(98mm)
4-1/2" x 3-13/16"
4-1/8" x 3-3/4"
(105mm x 95mm)
A = 3-13/16"
3-3/4"
(95mm)
Prior to operation:
u Install the appropriate cutting disc. Do not use excessively
worn discs. The maximum rotation speed of the tool must
not exceed that of the cutting disc.
u Make sure the disc rotates in the direction of the arrows
on the accessory and the tool.
u Secure the workpiece.
u Always set the spark deector correctly.
Switching on and off (g. 1)
The on/off trigger switch (N) is mounted in the operating
handle.
u To run the tool, press the on/off trigger switch (N).
u Keep the on/off switch depressed while performing the
operation.
u To stop the tool, release the trigger switch (N).
Warning: Do not switch the tool on or off when under load.
Warning: To prevent unauthorized use of tool, install a
standard padlock (not included) into the padlock hole (O)
located in the trigger switch.
&
Warning! Do not cut magnesium.
Consult your dealer for further information on the
appropriate accessories.
Performing a cut (g. 1)
u Place the material to be cut against the fence (E) and
secure using the vise (F).
u Switch on the tool and pull down the handle to cut the
workpiece. Allow the motor to reach full speed before
cutting.
u Allow the disc to cut freely. Do not force.
u After completing the cut, switch off the tool and return the
arm to its upper rest position.
Transporting (g. 1)
The tool is equipped with a lock chain (A) which locks the
tool in closed-down position for carrying.
Warning: Ensure that the tool is switched off and
disconnected from the mains supply before transporting.
u Lower the guard (K) onto the cutting table base (D) and
secure the tool in this position by securing the chain on
the hook in the handle.
u Transport the tool using the carrying handles.
u To release the tool, depress the operating handle slightly
and pull off the lock chain (A).
Maintenance
Your Black & Decker corded/cordless appliance/tool has been
designed to operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation depends
upon proper appliance/tool care and regular cleaning.
Warning! Before performing any maintenance on corded/
cordless appliance/tool:
u Switch off and remove the battery from the appliance.
u Keep the ventilation slots clear and regularly clean the
housing with a soft cloth.
u Do not use abrasive cleaners.
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be tted:
u Safely dispose of the old plug.
u Connect the brown lead to the live terminal in the new
plug.
u Connect the blue lead to the neutral terminal.
Warning! No connection is to be made to the earth terminal.
Follow the tting instructions supplied with good quality
plugs. Recommended fuse: 13 A.
Motor brush inspection and replacement (g. 9)
Warning! Turn off and unplug the tool. Be sure the trigger
switch is in the OFF position.
Brushes should be regularly inspected for wear. To inspect
brushes, remove brush cap (W). Brushes (V) should slide
freely in brush box. If brushes are worn down to .3" (8mm) as
shown in Figure 9 they should be replaced.
To reinstall, push new brush back into brush box. If replacing
existing brush, maintain same orientation as when removed.
Replace the brush cap (do not overtighten).
Cleaning
Blowing dust and grit out of the main housing by means of an
air hose is recommended and may be done as often as dirt is
seen collecting in and around the air vents. Always wear
proper eye and respiratory protection.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker CS355 T1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker CS355 T1 in the language / languages: English as an attachment in your email.

The manual is 0,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker CS355 T1

Black Decker CS355 T1 User Manual - English, German, Dutch, Danish, French, Italian - 100 pages

Black Decker CS355 T1 User Manual - Polish - 16 pages

Black Decker CS355 T1 User Manual - Portuguese, Swedish, Spanish, Norwegian, Finnish - 100 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info