709474

Black Decker CS1550 Manual

7
Zoom out
Zoom in
Previous page
1/76
Next page
7
ENGLISH
(Original instructions)
u Securely tighten the blade retaining screw by turning it
clockwise using the spanner (12) supplied.
u Adjust the riving knife as described below.
Fitting and removing the parallel fence (g. B)
u The parallel fence is used to saw in a straight line parellel
to the edge of the workpiece.
Fitting
u Loosen the locking knob (16).
u Insert the parallel fence (17) through the openings (18).
u Slide the parallel fence into the desired position.
u Tighten the locking knob.
Removing
u Loosen the locking knob.
u Pull the parallel fence off the tool.
Use
Warning! Let the tool work at its own pace. Do not overload.
Note: This tool can be used in the right hand or the left hand.
Adjusting the sawing angle (g. C)
The default angle between the saw blade and the shoe is 90°.
u Use a square to check that the angle between the saw
blade and the shoe is 90°. If the angle does not measure
90° adjust as follows:
u Loosen the locking knob (19) to unlock the saw shoe.
u Loosen the locknut (20) on the adjusting screw (21).
u Screw the adjusting screw in or out to achieve a 90°
angle.
u Retighten the locknut.
u Tighten the locking knob to lock the saw shoe in place.
Adjusting the depth of cut (g. D)
The depth of cut should be set according to the thickness of
the workpiece. It should exceed the thickness by approx. 2
mm.
u Loosen the knob (22) to unlock the saw shoe.
u Move the saw shoe (6) into the desired position.
The corresponding depth of cut can be read from the
scale (23).
u Tighten the knob to lock the saw shoe in place.
Adjusting the bevel angle (g. E)
This tool can be set to bevel angles between 0° and 45°.
u Loosen the locking knob (19) to unlock the saw shoe.
u Move the saw shoe (8) into the desired position. The cor-
responding bevel angle can be read from the scale (24).
u Tighten the locking knob to lock the saw shoe in place.
Switching on and off
u To switch the tool on, move the lock-off button (2) into the
unlock position and squeeze the on/off switch (1).
u To switch the tool off, release the on/off switch.
Sawing
Always hold the tool with both hands.
u Let the blade run freely for a few seconds before starting
the cut.
u Apply only a gentle pressure to the tool while performing
the cut.
u Work with the shoe pressed against the workpiece.
Hints for optimum use
u As some splintering along the line of cut on the top side of
the workpiece cannot be avoided, cut on the side where
splintering is acceptable.
u Where splintering is to be minimised, e.g. when cutting
laminates, clamp a piece of plywood onto the top of the
workpiece.
Using the sight guide (g. F)
The tool is equipped with a sight guide for straight cutting.
u Align the left edge of the guides (26) with the cutting line
(25).
u Keep the sight guide aligned with the cutting line while
sawing.
u Work with the shoe pressed against the workpiece.
Dust extraction (g. G)
An adaptor is required to connect a vacuum cleaner or dust
extractor to the tool.
u Insert the dust extraction adaptor (27) into the saw dust
outlet (10).
u Connect the vacuum cleaner hose (28) to the adaptor.
Maintenance
Your BLACK+DECKER corded/cordless appliance/tool has
been designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
Warning! Before performing any maintenance on corded/
cordless power tools:
u Switch off and unplug the appliance/tool.
u Or switch off and remove the battery from the appliance/
tool if the appliance/tool has a separate battery pack.
u Or run the battery down completely if it is integral and then
switch off.
u Unplug the charger before cleaning it. Your charger does
not require any maintenance apart from regular cleaning.
u Regularly clean the ventilation slots in your appliance/tool/
charger using a soft brush or dry cloth.
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker CS1550 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker CS1550 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info