Manual Black Decker CLM5448PC (page 14 of 176) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

709481

Zoom out

Zoom in

1/176

ENGLISH

(Original instructions)

ENGLISH

(Original instructions)

u The side marked “2” activates the right side battery port.

Note: The mower can be operated with a single battery pack if

the switch is in the correct position.

Active battery, state of charge indicators

Note: State of charge is only indicated when a battery pack

is inserted, or when the mower is turned on, or when a single

battery is present and the switch is toggled to connect it to run

the mower.

This mower is equipped with a state of charge indicator

located on the base of the dashboard (10). This is used to

display the active battery port and the current level of charge

in the active battery.

When a battery pack is installed into the battery ports, the

three charge level LEDs will illuminate for 3 seconds display-

ing the current level of charge in the battery and then turn off.

While the mower is in use the current level of charge for the

selected, active battery will be displayed.

u When the mower is rst activated, all of the LED indicator

lights on the dashboard (10) will temporarily illuminate.

u The dashboard LED lights on the inactive battery side will

turn off.

u The dashboard LEDs on the active battery side LED (17)

will remain lit and the three charge level indicator LEDs

(18) will indicate the percent of charge in the battery. (See

chart in gure A.)

u If no LEDs illuminate for the active battery, toggle the bat-

tery selection button (11) to the inactive battery. If neither

battery LEDs illuminate, charge the battery.

Note: The safety key has to be inserted for all of the LEDs

and switch functions to occur as described.

DUALVOLT 54V Battery Pack (Fig C1.)

The Dualvolt 54V battery pack can be used on 54V & 18V

Black+Decker Cordless tools. The battery can recognise

the tool it is inserted into and will run at the relevant power,

providing longer runtime in 18V tools. There is a State of

charge button (16b) which will indicate the level charge at both

54V & 18V.

Assembly

Warning! Before assembly, make sure the bail handle is

released and the safety key is removed.

Attaching lower handle

u Lift lower handle (4) into place making sure the arrow (19)

on the base of the mower lines up with 1, 2, or S on the

base of the handle (20) (inset of Figure F).

Note! Ensure each side of the lower handle is set on the

same number.

The arrow must be lined up with 1 or 2 for operation.

u Close the handle height adjust levers (6) as shown in

Figure F. As you close each, make sure the teeth are

engaged as shown in Figure G.

u If the connection between the handle and lever is too tight

or loose, open the lever and adjust the depth of the lever

by turning the lever. Close it again until the teeth are fully

clasped and each lever stays securely closed.

Attaching upper handle (g. H)

The upper handle has three different mounting position holes

(21) to adjust length of the handle from deck.

The rst set of holes near the bottom of the upper handle tube

allows for maximum handle length. Using the middle and top

mounting positions will shorten handle length

u Remove the upper-handle attachment levers (5), nuts

(22), and washers (23) from the handle.

u Line up the holes on the bottom of the upper handle (3)

with the holes on the top of the lower handle (4).

Note: Make sure the cord is located on the front of both han-

dles as shown in Figure I. If it is not it may result in the cord

tangling and the inability to easily store the mower.

u From the outside of the upper handle (3), slide the lever

bolt through the holes.

u Slide the washer over the bolt of the lever and loosely

assemble the entire assembly with the nut.

u Rotate the upper handle into its operating position.

u Close the lever. If it is too tight or too loose, open the lever

and the nut to adjust the clamping. Check the levers by

closing them. They should be tight enough so the handles

are held rmly, but loose enough so the levers can be fully

closed. Adjust by opening the lever and turning the nut

until the handles are secured.

Securing the motor cable (g. I)

Warning: Attach cable so that it does not become stretched or

pinched in the joints of the handles during use or folding. This

can cause damage to the cord.

The motor cable has to be xed to the handles using the

cable restraints that are already attached to the handle.

To clip the cable to the handle:

u Place the handles in operating position, see “Attaching

lower handle” section.

u Run the cable up the front of the lower and upper handles.

u Pull back the cable restraint.

u Slide the motor cable under the clip and ensure it is fully

held in place by the restraint.

Bagging

Warning: remove key and battery packs before removing side

discharge attachment and Mulching insert, and when opening

rear door cover and Installing bag.

u Ensure the side discharge attachment (26) (Figure M) and

the mulching insert (27) (Figure L) are removed from the

mower before bagging.

u Lift the rear door cover (9) and place the grass collection

bag (8) onto the mower so the bag hooks (28) rest on the

lugs (29) as shown in Figure K. Then lower the rear door

cover.

Mulching

Warning! Remove key and Battery packs before removing

Side discharge attachment and Collection bag, and when

Installing mulching insert.

u Ensure the side discharge attachment (26) and the collec-

tion bag (8) are not attached.

u Lift the rear door cover (9) and slide the mulching insert

(27) fully into the mower as shown in Figure L.

u Ensure the rear door cover fully closes before turning

mower on.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker CLM5448PC in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5,03 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker CLM5448PC Manual

Product: