586103
14
Zoom out
Zoom in
Previous page
1/20
Next page
14
ENGLISH
(Original instructions)
u Or switch off and remove the battery from the appliance/
tool if the appliance/tool has a separate battery pack.
u Or run the battery down completely if it is integral and then
switch off.
u Unplug the charger before cleaning it. Your charger does
not require any maintenance apart from regular cleaning.
u Regularly clean the ventilation slots in your tool/appliance
and charger using a soft brush or dry cloth.
u Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
u Regularly use a blunt scraper to remove grass and dirt
from the underneath of the guard.
Removing and installing the blade (g. S, T & U)
Warning! Do not touch the blade before the safety key has
been removed and the blades have come to a complete stop.
u Release the bail bar (2) to turn mower off, wait for the
blade to stop and remove the safety key (1).
u Cut a piece of wood (approximately 50 mm x 100 mm x
600 mm long) to use to keep the blade from turning while
removing the ange nut (29).
u Turn the mower on its side.
Warning! Wear gloves and proper eye protection. Be careful
of the sharp edges of the blade.
u Position the wood (28) and remove the ange nut (29)
with a 13 mm wrench (g. S).
u Remove the washer (30), blade (31), square blade guide
(32) and the fan (33) (g T). Examine the blade guide (32)
and fan (33) for damage and replace if necessary.
When tting the blade, make sure that the grass side of the
blade (Indicated by arrows on either end) will face the ground
when the mower is returned to its normal upright position.
u Install the fan (33). Be sure to position the fan blades (34)
so that they face in towards the mower.
u Install the blade guide (32). Be sure to position the 'D'
shaped pegs (35) so that they face out, away from the
mower.
u Be sure to align the ats on the on the fan (33) and the
blade guide (32) with the ats of the shaft.
u Fit the blade (31) onto the blade guide (32) with the ar-
rows facing outwards.
u Position the piece of wood (28) to keep the blade (31)
from turning (g. U).
u Install the washer (30) and ange nut (29) then tighten
with a 13mm wrench.
Blade sharpening (g. V)
Keep the blade sharp for best performance. A dull blade does
not cut grass cleanly or mulch properly.
Warning! Always make sure that the safety key is removed.
Warning! Wear proper eye protection while removing, sharp-
ening and installing a blade.
Sharpening the blade twice during a mowing season is usually
sufcient under normal circumstances. Sand causes the
blade to dull quickly. If your lawn has sandy soil more frequent
sharpening may be required.
u Replace bent or damaged blades immediately.
When sharpening the blade:
u Make sure that the blade remains balanced.
u Sharpen the blade at the original cutting angle.
u Sharpen the cutting edges on both ends of the blade,
removing equal amounts of material from both ends.
To sharpen a blade in a vice (g. V)
u Release the bail bar (2) to turn the lawnmower off and wait
for the blade to come to a complete stop.
u Remove the safety key (1) and the battery pack (22) and
turn the lawnmower on to its side.
u Remove the blade (31) from the mower, see the instruc-
tions for removing and installing blades.
Warning! Wear proper eye protection and gloves and be
careful of the sharp edges of the blade.
u Put the blade (31) in a vice.
u Carefully le the cutting edges of the blade with a ne
tooth le or a sharpening stone, maintaining the original
cutting edge.
u Check the balance of the blade, see the instructions for
blade balancing.
u Install the blade (31) on the mower and tighten securely,
see the instructions for removing and installing blades.
Blade balancing (g. W)
u Check the balance of the blade by putting the centre hole
in the blade on to a nail or a round shank screwdriver that
is clamped horizontally in a vice. If either end of the blade
rotates downward, le that end of the blade until the blade
is balanced.
Lubrication
No lubrication is necessary. Do not oil the wheels. They have
plastic bearing surfaces which require no lubrication.
Cleaning
u Release the bail bar (2) to turn the lawnmower off and wait
for the blade to come to a complete stop.
u Remove the safety key (1).
u Use only mild soap and a damp cloth to clean the mower.
u Use a blunt tool to clean out any clippings which may have
accumulated on the underside of the mower.
u After several uses, check all exposed fasteners for tight-
ness.
Preventing corrosion
Fertilisers and other garden chemicals contain agents which
greatly accelerate the corrosion of metals. If you mow in areas
where fertilisers or chemicals have been used, the mower
should be cleaned immediately afterward as follows:
u Release the bail bar (2) to turn the lawnmower off and wait
for the blade to come to a complete stop.
u Remove the safety key (1).
u Wipe all exposed parts with a damp cloth.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker CLM3820 T1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker CLM3820 T1 in the language / languages: English as an attachment in your email.

The manual is 4,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker CLM3820 T1

Black Decker CLM3820 T1 User Manual - English, German, Dutch, Danish, French, Italian - 164 pages

Black Decker CLM3820 T1 User Manual - Polish - 24 pages

Black Decker CLM3820 T1 User Manual - Portuguese, Swedish, Spanish, Norwegian, Finnish - 164 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info