586103
11
Zoom out
Zoom in
Previous page
1/20
Next page
11
ENGLISH
(Original instructions)
$
The charger is intended for
indoor use only.
Read the instruction manual
before use.
Electrical safety
#
Your charger is double insu-
lated; therefore no earth wire is
required. Always check that the
mains voltage corresponds to the
voltage on the rating plate. Never
attempt to replace the charger
unit with a regular mains plug.
u
If the supply cord is damaged, it must
be replaced by the manufacturer or
an authorised Black & Decker Service
Centre in order to avoid a hazard.
Features
This appliance includes some or all of the following features.
1. Safety key
2. Bail bar
3. Lock off release
4. Handle bar
5. Cable restraint clips
6. Upper handle
7. Upper handle quick release clamp
8. Grass box full indicator
9. Grass collection box
10. Lower Handle
11. Lower handle quick release clamp
12. Spring loaded rear door
13. Height adjust handle
14. Battery cover
15. Battery cover release
16. Handle
Assembly
Warning! Before assembly, make sure that the tool is
switched off and the safety key and battery have been
removed.
Assembling the grass collection box (g. A - C)
The grass box requires assembly before use and comes in 3
pieces.
u Clip the 2 sides of the grass collection box (9) together
(g.A). Make sure that all clips and guides are aligned.
u Align the lid (17) onto the assembled grass collection box.
Ensure that the guides and clips are aligned.
Note: Take extra care when aligning the clips at the rear of the
grass collection box.
u Push down on the lid to secure all clips. Begin at the
front and work towards the back. Ensure that all clips are
securely located.
Fitting the lower handle (g. D & E)
u Remove the lower handle quick release clamps (11) from
the base of the mower.
u Place the lower handle (10) around the base, making
sure the three notches (18) on the lower handle (10) face
toward the top.
u Screw the lower handle quick release clamps (11) through
the lower handle into the mower base, With the lower
handle quick release clamps screwed in half way, close
the quick release clamps (g.E) and ensure the teeth of
the handle and base interlock. If the connection between
the handle and quick release clamps is too tight or loose,
adjust the depth of the quick release clamps and close
them again until the teeth are fully closed.
Fitting the upper handle (g. F & G)
u Fit the upper handle (6) to the lower handle (10) using the
upper handle quick release clamps (7) and clamp nuts
(19) as shown.
u Screw the upper handle quick release clamps (7) through
the lower handle into the clamp nuts (20), With the
upper handle quick release clamps screwed in half way,
close the quick release clamps (g. G). If the connection
between the handle and quick release clamps is too tight
or loose, adjust the depth of the quick release clamps and
close them again until the teeth are fully closed.
Adjusting the height of the handle (g. H)
u Release the lower handle quick release clamp as shown.
u Lift or lower the handle into one of the 3 marked positions
next to the lower handle quick release clamps.
u Close the lower handle quick release clamps (11) and
ensure the teeth of the handle and base interlock. If the
connection between the handle and quick release clamps
is too tight or loose, adjust the depth of the quick release
clamps and close them again until the teeth are fully
closed.
Securing the motor cable
The motor cable has to be xed using the cable restraint.
u Secure the cable to the upper and lower handle by cliping
it into the cable restraint clips (5)
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker CLM3820 T1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker CLM3820 T1 in the language / languages: English as an attachment in your email.

The manual is 4,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker CLM3820 T1

Black Decker CLM3820 T1 User Manual - English, German, Dutch, Danish, French, Italian - 164 pages

Black Decker CLM3820 T1 User Manual - Polish - 24 pages

Black Decker CLM3820 T1 User Manual - Portuguese, Swedish, Spanish, Norwegian, Finnish - 164 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info