462018
7
Zoom out
Zoom in
Previous page
1/72
Next page
7
ENGLISH
 If the supply cord is damaged, it must be re-
placed by the manufacturer or an authorised
Black & Decker Service Centre in order to avoid
a hazard.
Features
1. Variable speed switch
2. Lock-on button
3. Forward/reverse button
4. Drilling mode selector
5. Chuck
6. Depth stop (not all models)
7. Side handle (not all models)
g. B
8. Manual spindle lock button (single sleeve key-
less chuck only)
Assembly
Warning! Before assembly, make sure that the tool
is switched off and unplugged.
Fitting the side handle and depth stop ( g. A)
 Turn the grip counter clockwise until you can
slide the side handle (7) onto the front of the
tool as shown.
 Rotate the side handle into the desired posi-
tion.
 Insert the depth stop (6) into the mounting hole
as shown.
 Set the drilling depth as described below.
 Tighten the side handle by turning the grip
clockwise.
Fitting a drill bit
Single sleeve keyless chuck ( g. B)
 Open the chuck by pressing the manual spindle
lock button (8) and turning the sleeve (9) counter
clockwise.
 Insert the bit shaft (12) into the chuck.
 Firmly tighten the chuck by pressing the manual
spindle lock button (8) and turning the sleeve
clockwise until it is tight.
Two sleeve keyless chuck ( g. C)
 Open the chuck by turning the sleeve (13) coun-
ter clockwise.
 Insert the bit shaft (12) into the chuck and rmly
tighten the chuck.
Keyed chuck ( g. D)
 Open the chuck by turning the sleeve (11) coun-
ter clockwise.
 Insert the bit shaft (12) into the chuck.
 Insert the chuck key (14) into each hole (15) in
the side of the chuck and turn clockwise until
tight.
Removing and re tting the chuck ( g. E)
 Open the chuck as far as possible.
 Remove the chuck retaining screw, located
in the chuck, by turning it clockwise using
a screwdriver.
 Tighten an Allen key into the chuck and strike it
with a hammer as shown.
 Remove the Allen key.
 Remove the chuck by turning it counter clock-
wise.
 To re t the chuck, screw it onto the spindle and
secure it with the chuck retaining screw.
Residual risks
Additional residual risks may arise when using the
tool which may not be included in the enclosed
safety warnings. These risks can arise from misuse,
prolonged use etc.
Even with the application of the relevant safety
regulations and the implementation of safety de-
vices, certain residual risks cannot be avoided.
These include:
 Injuries caused by touching any rotating/moving
parts.
 Injuries caused when changing any parts,
blades or accessories.
 Injuries caused by prolonged use of a tool. When
using any tool for prolonged periods make sure
you take regular breaks.
 Impairment of hearing.
 Health hazards caused by breathing dust devel-
oper when using your tool (example:- working
with wood, especially oak, beech and MDF).
Use
Warning! Let the tool work at its own pace. Do not
overload.
Warning! Before drilling into walls, oors or ceilings,
check for the location of wiring and pipes.
Selecting the direction of rotation ( g. F)
For drilling and for tightening screws, use forward
(clockwise) rotation. For loosening screws or re-
moving a jammed drill bit, use reverse (counter
clockwise) rotation.
 To select forward rotation, push the forward/re-
verse button (3) to the left position.
 To select reverse rotation, push the forward/re-
verse button to the right.
Warning! Never change the direction of rotation
while the motor is running.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker CD714CRES at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker CD714CRES in the language / languages: English, German, French, Turkish as an attachment in your email.

The manual is 2,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info