Manual Black Decker CD700 T1 (page 26 of 80) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian, Finnish)

577916

Zoom out

Zoom in

1/80

ENGLISH

placed on the

stands (4). Always

point your

heatgun away

from you. Secure

the cable to

prevent pulling

your heatgun off

the stand. Do not

touch the nozzle

and ensure that

nothing is

dropped into the

nozzle. Carefully switch off your heatgun and then

allow it to cool (see cooling down procedure).

FITTING THE SCRAPER (KX1682, KX1683)

Ensure your heatgun is cool.

Align the slot of

the scraper blade

with the

protrusion on the

blade holder and

position under the

retaining screw.

Note: Ensure the hole in the scraper is to the left of the

screw in the blade holder.

Tighten the

retaining screw.

Place the blade

holder over the

nozzle outlet.

Ensure it is

aligned. The small

bump on the

inside of the blade

holder engages with the recess on the nozzle. Tighten

the blade holder clamp screw.

PAINT STRIPPING

When stripping a

point next to

glass, it is

necessary to

protect the glass

from the heat.

A Black & Decker

glass protector

nozzle is used for

this purpose (available as an accessory). Your heatgun

is not suitable for stripping metal framed windows.

This is because the heat from the heatgun is

conducted through the metal and can crack the glass.

Scrape with the grain of the wood wherever possible.

Do not linger on one spot for too long as the surface

may char or ignite.

KX1682, KX1683 only:

Your heatgun is designed for use with the scraper

blade to strip paint.

Proceed as follows:

Ensure the nozzle

is cool and fit the

scraper blade.

Hold your heatgun

with the scraper

blade in contact

with the surface

at an angle of 30-40˚.

When the paint softens, scrape firmly. Experiment to

establish the length of time necessary to apply the heat

to obtain optimum results. Scrape the softened paint

immediately or it will harden again.

Take care to prevent paint and debris collecting on the

scraper because it may ignite. Carefully clean the

scraper blade with a knife should any build up occur.

When scraping vertical surfaces, scrape downwards

to prevent debris falling into the nozzle.

Note: When stripping a point next to glass, use a glass

protector nozzle instead of the scraper blade - a

manual scraper is needed to scrape off the paint.

CD700, KX1600 only:

Your heatgun is designed to soften paint and laquer

enabling it to be removed using a good quality

hand scraper.

Proceed as follows:

Direct the hot air onto the area to be removed. When

the paint softens, scrape firmly. Experiment to establish

the length of time necessary to apply the heat to obtain

optimum results. Scrape the softened paint

immediately or it will harden again.

OTHER USES FOR YOUR HEATGUN

On low heat (KX1682, KX1683):

• Drying paint and varnish.

• Removing stickers and decorations.

• Waxing and dewaxing (eg. ski’s).

• Drying wet timber prior to filling.

• Shrinking PVC wrapping and insulation tubes.

• Thawing frozen pipes.

30-40°

CD700 KX1600-1683 ML p22-39 07/01/2000, 3:39 pm26

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker CD700 T1 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,47 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker CD700 T1 Manual

Product: