3362
4
Zoom out
Zoom in
Previous page
1/64
Next page
4
ENGLISH
When disposing of batteries, follow the instructions given
in the section “Protecting the environment”.
Under extreme conditions, battery leakage may occur.
When you notice liquid on the battery, proceed as follows:
- Carefully wipe the liquid off using a cloth. Avoid skin
contact.
- In case of skin or eye contact, follow the instructions below.
Warning! The battery fluid, a 25-30% solution of potassium
hydroxide, can be harmful. In case of skin contact, immediately
rinse with water. Neutralise with a mild acid such as lemon
juice or vinegar. In case of eye contact, rinse abundantly with
clean water for at least 10 minutes. Consult a physician.
Fire hazard! Avoid short-circuiting the contacts of a
detached battery (e.g. when storing the battery in a
toolbox).
Do not incinerate the battery.
Do not attempt to charge damaged batteries.
Chargers
Use your Black & Decker charger only to charge batteries
of the type supplied with your tool. Other batteries could
burst, causing personal injury and damage.
Never attempt to charge non-rechargeable batteries.
Have defective cords replaced immediately.
Do not expose to water.
Do not open the charger.
Do not probe the charger.
The charger is intended for indoor use only.
Electrical safety
Your charger is double insulated; therefore no earth
wire is required. Always check that the mains voltage
corresponds to the voltage on the rating plate.
Never attempt to replace the charger unit with a
regular mains plug.
Features
This tool includes some or all of the following features.
1. Variable speed switch or two-speed on/off switch
2. Forward/reverse slider
3. Mode selector / torque adjustment collar
4. Chuck
5. Battery
6. Battery release button
Fig. D & E
7. Charger
8. Charging base
9. Charger connector
10. Charger plug
Assembly
Fitting and removing the battery (fig. A)
To fit the battery (5), line it up with the receptacle on the
tool. Slide the battery into the receptacle and push until
the battery snaps into place.
To remove the battery, push the two release buttons (6)
simultaneously while at the same time pulling the battery
out of the receptacle.
Fitting and removing a drill bit or screwdriver bit (fig. B)
Warning! First remove the battery from the tool.
This tool is fitted with a keyless chuck to allow for an easy
exchange of bits.
Lock the tool by setting the forward/reverse slider (2) to
the centre position.
Open the chuck by turning the front part (11) with one
hand while holding the rear part (12) with the other (fig. B).
Insert the bit shank (13) into the chuck.
Firmly tighten the chuck by turning the front part (11) with
one hand while holding the rear part (12) with the other.
Removing and refitting the chuck (fig. C)
Open the chuck as far as possible.
Remove the chuck retaining screw by turning it clockwise
using a screwdriver.
Tighten an Allen key (14) into the chuck and strike it with
a hammer as shown.
Remove the Allen key.
Remove the chuck by turning it counterclockwise.
To refit the chuck, screw it onto the spindle and secure it
with the chuck retaining screw.
Use
Charging the battery
The battery needs to be charged before first use and whenever
it fails to produce sufficient power on jobs that were easily
done before. A new battery, or a battery that has not been
used for an extended period of time, achieves full performance
only after approx. 5 charging and discharging cycles.
The battery may become warm while charging; this is normal
and does not indicate a problem.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker CD18 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker CD18 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info