578557
9
Zoom out
Zoom in
Previous page
1/100
Next page
9
ENGLISH
u Place the guard (4) onto the tool as shown.
u Place the ange (8) over the spindle with the protruding
pips towards the guard. Make sure that the holes in the
ange align with the screw holes.
u Secure the ange with the screws (9). Make sure that the
screws are fully tight and that the guard can be rotated.
Removing
u Use a screwdriver to remove the screws (9).
u Remove the ange (8), guard (4) and spring washer (7).
Store these parts carefully.
Warning! Never use the tool without the guard.
Fitting the side handle
u Screw the side handle (2) into one of the mounting holes
in the tool.
Warning! Always use the side handle.
Fitting and removing grinding or cutting discs
(g.C-E)
Always use the correct type of disc for your application.
Always use discs with the correct diameter and bore size
(see technical data).
Fitting
u Fit the guard as described above.
u Place the inner ange (10) onto the spindle (5) as shown
(g. C). Make sure that the ange is correctly located on
the at sides of the spindle.
u Place the disc (11) onto the spindle (5) as shown (g. C).
If the disc has a raised centre (12), make sure that the
raised centre faces the inner ange.
u Make sure that the disc locates correctly on the inner ange.
u Place the outer ange (13) onto the spindle. When tting
a grinding disc, the raised centre on the outer ange must
face towards the disc (A in g. D). When tting a cutting
disc, the raised centre on the outer ange must face away
from the disc (B in g. D).
u Keep the spindle lock (3) depressed and tighten the outer
ange using the two-pin spanner (14) (g. E).
Removing
u Keep the spindle lock (3) depressed and loosen the outer
ange (13) using the two-pin spanner (14) (g. E).
u Remove the outer ange (13) and the disc (11).
Fittingandremovingsandingdiscs(g.E&F)
For sanding, a backing pad is required. The backing pad is
available from your Black & Decker dealer as an accessory.
Fitting
u Place the inner ange (10) onto the spindle (5) as shown
(g. F). Make sure that the ange is correctly located on
the at sides of the spindle.
u Place the backing pad (15) onto the spindle.
u Place the sanding disc (16) onto the backing pad.
u Place the outer ange (13) onto the spindle with the raised
centre facing away from the disc.
u Keep the spindle lock (3) depressed and tighten the outer
ange using the two-pin spanner (14) (g. E). Make sure
that the outer ange is tted correctly and that the disc is
clamped tightly.
Removing
u Keep the spindle lock (3) depressed and loosen the outer
ange (13) using the two-pin spanner (14) (g. E).
u Remove the outer ange (13), the sanding disc (16) and
the backing pad (15).
Use
Warning! Let the tool work at its own pace. Do not overload.
u Carefully guide the cable in order to avoid accidentally
cutting it.
u Be prepared for a stream of sparks when the grinding or
cutting disc touches the workpiece.
u Always position the tool in such a way that the guard
provides optimum protection from the grinding or cutting disc.
Switching on and off
u To switch on, slide the on/off switch (1) forward. Note that
the tool will continue running when you release the switch.
u To switch off, press the rear part of the on/off switch.
Warning! Do not switch the tool off while under load.
Hints for optimum use
u Firmly hold the tool with one hand around the side handle
and the other hand around the main handle.
u When grinding, always maintain an angle of approx. 15°
between the disc and the workpiece surface.
Maintenance
Your Black & Decker corded/cordless appliance/tool has been
designed to operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation depends
upon proper tool care and regular cleaning.
Warning! Before performing any maintenance on corded/
cordless power tools:
u Switch off and unplug the appliance/tool.
u Or switch off and remove the battery from the appliance/
tool if the appliance/tool has a separate battery pack.
u Or run the battery down completely if it is integral and then
switch off.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker CD110 T3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker CD110 T3 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info