Manual Black Decker cd 602 (page 8 of 100) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Spanish, Norwegian, Finnish)

382789

Zoom out

Zoom in

1/100

ENGLISH

Electrical safety

This tool is double insulated; therefore no earth wire

is required. Always check that the power supply

corresponds to the voltage on the rating plate.

u If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Black & Decker Service

Centre in order to avoid a hazard.

Features

1. On/off switch

2. Lock-off button

3. Main handle

4. Secondary handle

5. Mitre angle scale

6. Locking knob for mitre angle adjustment

7. Parallel fence

8. Shoe

9. Saw blade

10. Saw blade guard

11. Riving knife

12. Depth of cut scale

13. Locking knob for depth of cut adjustment

14. Spanner

15. Saw dust outlet

Assembly

Warning! Before attempting any of the following operations,

make sure that the tool is switched off and unplugged and that

the saw blade has stopped.

Removingandttingasawblade(g.A)

Caution! This method for changing the blade is only for use

with blades that contain a hole (16) for the purpose of locking

the blade whilst tting and removing.

Removing

u Insert a screwdriver into the hole (16) to prevent the saw

blade from rotating.

u Loosen and remove the blade retaining screw (17) by

turning it counterclockwise using the spanner (14) supplied.

u Remove the outer washer (18).

u Remove the saw blade (9).

Fitting

u Place the saw blade onto the inner washer (19), making

sure that the arrow on the blade points in the same

direction as the arrow on the tool.

u Fit the outer washer (18) on the spindle, with the raised

part pointing away from the saw blade.

u Insert the blade retaining screw (17) into the hole.

u Insert a screwdriver into the hole (16) to prevent the saw

blade from rotating.

u Securely tighten the blade retaining screw by turning it

clockwise using the spanner (14) supplied.

u Adjust the riving knife as described below.

Warning! Whenever a new blade is tted the saw blade guard

should be checked to ensure that it can move freely.

Removingandttingasawblade(g.B)

Caution! This method is for changing blades that do not

contain a hole (16) for the purpose of locking the blade whilst

tting and removing.

Removing

u Set the depth of cut on the saw to 10mm.

u Place a plank of wood on the floor, then place the saw

onto the leading edge of the wood as shown in fig B to

prevent the blade from turning.

u Whilst applying firm pressure on the saw, loosen and

remove the blade retaining screw (17) by turning it

counterclockwise using the spanner (14) supplied.

u Remove the outer washer (18).

u Remove the saw blade (9).

Fitting

u Place the saw blade onto the inner washer (19), making

sure that the arrow on the blade points in the same

direction as the arrow on the tool.

u Fit the outer washer (18) on the spindle, with the raised

part pointing away from the saw blade.

u Insert the blade retaining screw (17) into the hole loosely

tighten by hand.

u Place a plank of wood on the floor, then place the saw

onto the leading edge of the wood as shown in fig B to

prevent the blade from turning.

u Whilst applying firm pressure on the saw, securely tighten

blade retaining screw (17) by turning it clockwise using the

spanner (14) supplied.

u Adjust the riving knife as described below.

Warning! Whenever a new blade is tted the saw blade guard

should be checked to ensure that it can move freely.

Adjustingtherivingknife(g.C)

The riving knife prevents the saw blade from jamming during

rip sawing operations. The riving knife must be adjusted after

replacing the saw blade.

u Loosen the screw (20) holding the riving knife in position.

u Position the riving knife (11) as shown.

The distance between the toothed rim and the riving knife

should be 2 - 3 mm.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker cd 602 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,2 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker cd 602 Manual

Product: