Manual Black Decker BSA34 (page 25 of 92) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Spanish, Norwegian, Finnish)

16270

Zoom out

Zoom in

1/92

20 en - 5

ENGLISH

The battery pack can be removed at any time or

left in the connected charger indefinitely.

• The red charging indicator flashes rapidly to

indicate a charging problem. Reinsert the battery

pack or try a new one. If the new pack also

refuses to charge, have your charger tested by

an authorized Elu repair agent.

• When plugged into power sources such as

generators or sources that convert DC to AC,

the red charging indicator may blink twice,

switch off and repeat. This indicates a temporary

problem of the power source. The charger will

automatically switch back to normal operation.

Inserting and removing the battery pack

• Insert the battery pack into the grip (8) until it

clicks in place.

• To remove the battery pack, press the two

release buttons (10) simultaneously and pull the

pack out of the grip (8).

Inserting and removing bits (fig. A & B)

• Open the chuck by turning the sleeve (13)

counterclockwise and insert the bit shank.

• Place the bit in the chuck as far as it will go and

lift slightly before tightening.

• Tighten firmly by turning the sleeve clockwise.

• To remove the bit, proceed in reverse order.

Selecting the operating mode or adjusting the

torque (fig. C)

The collar of this tool has 15 positions for the

adjustment of the torque to suit the size of the screw

and the workpiece material. For torque adjustment,

refer to the section “Screwdriving”.

• Select the drilling mode or torque by aligning the

symbol or number on the collar (5) with the

indicator (14) on the housing.

Forward/reverse slider (fig. D)

• To select forward or reverse rotation, use the

forward/reverse slider (2) as shown (see arrows

on tool).

Always wait until the motor has come to

a complete standstill before changing the

direction of rotation.

Two gear selector (fig. E)

Your tool is fitted with a two gear selector (6) to vary

the speed/torque ratio.

1 low speed/high torque

(drilling large holes, driving screws)

2 high speed/low torque

(drilling smaller holes)

For speed rates, refer to the technical data.

• Always push the two gear selector

completely forward or backward.

• Do not change gears at full speed or

during use.

Removing and fitting the chuck (fig. F & G)

• Open the chuck jaws as far as possible.

• Insert a screwdriver into the chuck and remove

the chuck retaining screw by turning clockwise

as shown in figure F.

• Tighten an Allen key into the chuck and strike it

with a hammer as shown in figure G. This will

loosen the chuck so that it can be unscrewed by

hand.

• To refit the chuck, proceed in reverse order.

Instructions for use

• Always observe the safety instructions

and applicable regulations.

• Be aware of the location of pipework and

wiring.

• Apply only a gentle pressure to the tool.

Excessive force does not speed up

drilling but decreases tool performance

and may shorten tool life.

• To minimise stalling on break-through,

progressively reduce the drill point

pressure towards the end of the operation.

• Keep the motor running when pulling the

bit back out of a drilled hole. This will

help prevent jamming.

Prior to operation:

• Make sure your battery pack is (fully) charged.

• Insert the appropriate bit.

• Mark the spot where the hole is to be drilled.

• Select forward or reverse rotation.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker BSA34 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,18 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker BSA34 Manual

Product: