Manual Black Decker BES700 (page 9 of 148) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

709449

Zoom out

Zoom in

1/148

ENGLISH

(Original instructions)

burn the lower guard, the kerf insert and other plastic

parts.

u Use clamps to support the workpiece whenever

possible. If supporting the workpiece by hand, you

must always keep your hand at least 100 mm from

either side of the saw blade. Do not use this saw to

cut pieces that are too small to be securely clamped

or held by hand. If your hand is placed too close to the

saw blade, there is an increased risk of injury from blade

contact.

u The workpiece must be stationary and clamped or

held against both the fence and the table. Do not feed

the workpiece into the blade or cut “freehand” in any

way. Unrestrained or moving workpieces could be thrown

at high speeds, causing injury.

u Push the saw through the workpiece. Do not pull the

saw through the workpiece. To make a cut, raise the

saw head and pull it out over the workpiece without

cutting, start the motor, press the saw head down and

push the saw through the workpiece.

Cutting on the pull stroke is likely to cause the saw blade

to climb on top of the workpiece and violently throw the

blade assembly towards the operator.

u Never cross your hand over the intended line of cut-

ting either in front or behind the saw blade. Supporting

the workpiece “cross handed” i.e. holding the workpiece to

the right of the saw blade with your left hand or vice versa

is very dangerous.

u Do not reach behind the fence with either hand closer

than 100 mm from either side of the saw blade, to

remove wood scraps, or for any other reason while

the blade is spinning. The proximity of the spinning saw

blade to your hand may not be obvious and you may be

seriously injured.

u Inspect your workpiece before cutting. If the work-

piece is bowed or warped, clamp it with the outside

bowed face toward the fence. Always make certain

that there is no gap between the workpiece, fence

and table along the line of the cut. Bent or warped

workpieces can twist or shift and may cause binding on

the spinning saw blade while cutting. There should be no

nails or foreign objects in the workpiece.

u Do not use the saw until the table is clear of all tools,

wood scraps, etc., except for the workpiece. Small de-

bris or loose pieces of wood or other objects that contact

the revolving blade can be thrown with high speed.

u Cut only one workpiece at a time. Stacked multiple

workpieces cannot be adequately clamped or braced and

may bind on the blade or shift during cutting.

u Ensure the mitre saw is mounted or placed on a level,

rmworksurfacebeforeuse. A level and rm work sur-

face reduces the risk of the mitre saw becoming unstable.

u Plan your work. Every time you change the bevel or

mitre angle setting, make sure the adjustable fence is

set correctly to support the workpiece and will not

interfere with the blade or the guarding system. With-

out turning the tool “ON” and with no workpiece on the

table, move the saw blade through a complete simulated

cut to assure there will be no interference or danger of

cutting the fence.

u Provideadequatesupportsuchastableextensions,

saw horses, etc. for a workpiece that is wider or

longer than the table top. Workpieces longer or wider

than the mitre saw table can tip if not securely supported.

If the cut-off piece or workpiece tips, it can lift the lower

guard or be thrown by the spinning blade.

u Do not use another person as a substitute for a table

extension or as additional support. Unstable support

for the workpiece can cause the blade to bind or the

workpiece to shift during the cutting operation pulling you

and the helper into the spinning blade.

u The cut-off piece must not be jammed or pressed by

any means against the spinning saw blade.

If conned, i.e. using length stops, the cut-off piece could

get wedged against the blade and thrown violently.

u Alwaysuseaclamporaxturedesignedtoproperly

support round material such as rods or tubing. Rods

have a tendency to roll while being cut, causing the blade

to “bite” and pull the work with your hand into the blade.

u Let the blade reach full speed before contacting the

workpiece. This will reduce the risk of the workpiece

being thrown.

u If the workpiece or blade becomes jammed, turn the

mitre saw off. Wait for all moving parts to stop and

disconnect the plug from the power source and/or re-

move the battery pack. Then work to free the jammed

material. Continued sawing with a jammed workpiece

could cause loss of control or damage to the mitre saw.

u Afternishingthecut,releasetheswitch,holdthe

saw head down and wait for the blade to stop before

removing the cut-off piece. Reaching with your hand

near the coasting blade is dangerous.

Additional safety instructions for mitre saws

u Holdthehandlermlywhenmakinganincompletecut

or when releasing the switch before the saw head is

completely in the down position. The braking action of

the saw may cause the saw head to be suddenly pulled

downward, causing a risk of injury.

u The intended use is described in this instruction manual.

The use of any accessory or attachment or performance

of any operation with this tool other than those recom-

mended in this instruction manual may present a risk of

personal injury and/or damage to property.

u Do not use cracked/bent/damaged/deformed saw blades.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker BES700 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 12,24 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker BES700 Manual

Product: