Manual Black Decker BEMWH551 (page 11 of 132) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

709479

Zoom out

Zoom in

1/132

ENGLISH

(Original instructions)

6. Lower handle

7. Motor cover

8. Lower handle latch

9. Blade bolt spanner

Assembly

Warning! Before assembly, make sure that the appliance is

switched off and unplugged.

Attaching the lower handle to the main body

(Fig. A)

u Align the holes on the lower handle (6) with the holes on

the main body (8a).

Insert the lower handle latch (8) and push until secure as

shown in gure A.

Attaching the upper handle to the lower handle

(Fig. B)

u Align the holes on the lower handle (6) with the

corresponding holes on the upper handle (1).

u Insert the screw (5b) through both handles and t the

washer (5a).

u Place the upper handle latch (5) onto the screw (5b) and

tighten until secure as shown in gure B.

Note: The upper handle can be attached to the lower handle

with the upper handle latch (5) located either on the outside or

the inside, depending on personal preference.

Before starting

u Before use, check that the mower is in good

working order.

u Ensure the power button is in the off position and

disconnect the cable plug from the mains supply.

u Examine the general condition of the mower.

Inspect the body underneath the deck, blade,

switch, power cord and extension cord (if used).

u Check for loose screws, misalignment, binding

of moving parts, improper mounting, broken

parts and any other condition that may affect

its safe operation.

u If abnormal noise or vibration occurs during operation,

turn the mower off immediately and have the problem

corrected. Do not use a damaged tool and attach a label

“DO NOT USE” to the tool. Ensure that you are on a at

surface and have secure footing. Check that the

latches (5, 8) are securely tightened.

Switching on and off (Fig. C, D)

Note: Practise switching on and switching off the mower as

detailed below before using it to cut grass for the rst time.

Start the mower on a hard, level surface (such as a driveway)

that is free of debris. Connect the power cordset to the power

point.

u Squeeze the motor on/off grip (2) towards the upper

handle (1) and use the other hand to press the power

button (3) as shown in gure C. The power button remains

depressed as long as the pressure is maintained on the

motor on/off grip (2).

u Transfer the other hand to the upper handle (1). As

the motor picks up speed, the mower lifts on a cushion

of air, making it very light to handle and extremely

manoeuvrable. To stop the motor, release pressure on the

motor on/off grip (2) until the power button (3) clicks off.

The mower sinks to the ground. The motor is not

started if pressure is re-applied to the motor on/off grip (2)

alone. It is necessary to squeeze the motor on/off grip (2)

and re-press the power button (3) to re-start the motor.

Emergency stop

u To stop the motor in an emergency, simply release the

pressure on the motor on/off grip.

u Keep your hands on the upper handle in order to control

the mower as it sinks to the ground.

u Allow the motor to stop completely before releasing

control of the handle.

Changing the mower blades (Fig. E, F)

Warning! Never carry out any assembly operations or

adjustments with the power connected to the mower. Always

ensure that the power button is in the off position and that the

power plug is disconnected from the supply.

Periodically check the blades (11) for damage and balance.

If there are broken ends or other damage or the two blades

are out of balance they must both be replaced.

With the power button (3) in the off position and the power

plug removed from the supply, turn the mower on its back as

shown in gure E.

u Unclip the old blades (11) from the pins (12) and replace

them with new ones.

u Return the mower to the upright position.

u Reconnect the power cable to the supply and run the

mower for a few minutes to check that the blades are

properly tted and that there is no undue noise or

vibration.

u Use only blades as recommended by the manufacturer.

To change from a 28mm to a 38mm cut (Fig.G, H, I)

u Use the blade bolt spanner (9) to remove the blade bolt

(9a).

u Remove the blade holder disc (10) and replace it the other

way around.

u Remove the blades (11) from their anchor pins (12) on the

underside of the blade holder disc (10).

u Replace the blades on the anchor pins on the upper side

of the blade holder disc (10).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker BEMWH551 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,66 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker BEMWH551 Manual

Product: