Manual Black Decker BDV090 T1 (page 6 of 76) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

581374

Zoom out

Zoom in

1/76

ENGLISH

(Original instructions)

Check the polarity of the battery posts. A positive (POS,P, +)

battery post usually has a larger diameter than the negative

(NEG, N, -) battery post.

Connect the positive (red) clamp from the battery charger to

the positive (POS, P, +) post of the battery.

Connect the negative (black) clamp from the battery charger

to the negative (NEG, N, -) post of the battery.

When disconnecting the battery charger from the battery,

always:

u Switch off and unplug the battery charger.

u Remove the negative (black) clamp rst.

u Remove the positive (red) clamp last.

u Ret any insulating covers to the battery posts.

Use

Connecting the appliance with the battery clamps

(g. A)

Warning! Always disconnect the ac plug from the ac mains

socket before connecting or disconnecting the appliance to or

from the battery.

Warning! Never connect any of the accessory leads together

as this will cause a hazard. The accessory leads should only

ever be connected to the in-line connector (6).

u Connect the battery clamps (3) to the battery charger with

the in-line connector (6).

u The appliance's output leads have colour-coded battery

clamps (3) (red-positive and black-negative). These

connect directly to the corresponding connectors on the

battery terminals.

u Follow the steps outlined in "Safety instructions" at the

front of this manual.

u Insert the ac plug of the battery charger into an ac mains

socket.

Connecting the appliance with the ring terminals

(g. A & B)

Warning! Always disconnect the ac plug from the ac mains

socket before connecting or disconnecting the appliance to or

from the battery.

Warning! Never connect any of the accessory leads together

as this will cause a hazard. The accessory leads should only

ever be connected to the in-line connector (6).

u Connect the ring terminals (4) to the battery charger with

the in-line connector (6).

u The output leads have crimped, colour-coded ring

terminals (4) (red-positive and black-negative). The ring

terminals (4) connect directly to the corresponding con-

nectors on the battery terminals.

u Remove the nuts from the bolts of the battery terminal's

connectors (g. B).

u Install the red ring terminal (4) to the bolt of the positive

battery terminal connector and replace the nut.

u Install the black ring terminal (4) to the bolt of the negative

terminal connector and replace the nut.

u Insert the ac plug of the battery charger into an ac mains

socket.

Connecting the appliance with the dc accessory

plug (g. A)

Warning! Always disconnect the ac plug from the ac mains

socket before connecting or disconnecting the appliance to or

from the battery.

Warning! Never connect any of the accessory leads together

as this will cause a hazard. The accessory leads should only

ever be connected to the in-line connector (6).

u Connect the dc accessory plug (5) to the battery charger

with the in-line connector (6).

u Insert the dc accessory plug (5) into the vehicle's dc ac-

cessory outlet.

u Insert the ac plug of the battery charger into an ac mains

socket.

Charging Indicators

u Red LED (2) - bad connection, the battery is not able to

accept charge or a reverse polarity connection has been

detected.

u Flashing green LED (2) - good connection and the battery

is charging.

u Solid green LED (2) - the battery is fully charged.

When the appliance is properly connected, the yellow LED will

illuminate, indicating that the smart circuit is functioning to as-

sess the status of the battery. This procedure may take up to 2

minutes if the battery voltage is lower than 12.8 Volts.

The appliance is fully automatic; it will power on when needed

and power off when the battery is fully-charged.

The appliance has built-in circuit protection which guards

against overcharging or short circuits.

Charging the battery (g. C)

u Slide the charge voltage selector switch (1) to the 6V or

12V position as required.

u Leave the appliance on.

u Monitor the battery from time to time.

Note: A clicking sound may occur during the charging proc-

ess, this is normal.

u When the solid green LED is lit, the battery is fully

charged.

u Remove the ac plug from the ac mains socket.

u Remove the charging leads from the battery.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker BDV090 T1 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,38 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker BDV090 T1

Black Decker BDV090 T1 Quick start guide - English - 12 pages

Black Decker BDV090 T1 User Manual - Polish - 12 pages

Black Decker BDV090 T1 User Manual - Turkish - 12 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker BDV090 T1 Manual

Product: