53625
5
Zoom out
Zoom in
Previous page
1/72
Next page
5
ENGLISH
To check the battery charge status at any time, turn the unit
on by pressing the on/off button (3). The unit will beep once
and the red power LED (11) and the battery status LED (13)
will light.
The battery status LED (13) displays the level of charge:
X If the battery status LED (13) lights red charge the unit.
X If the battery status LED (13) lights green the unit is fully
charged.
Charging the unit with the mains charger (fig. A)
Make sure that the LED area light is turned off while the unit
is being charged.
X Turn the unit on by pressing the on/off button (3). The unit
will beep once and the red power LED (11) and the battery
status LED (13) will light.
X Connect the mains charging adaptor (9) into the 12 Vdc
charging socket (7) on the top of the unit.
X Insert the mains charging adaptor (9) into a mains power
socket.
X Press the recharge unit button (5). The unit will beep once
and the green battery status LED (13) will flash, indicating
that the unit is charging.
Warning! The unit will beep continuously and the battery
status LED (13) will flash red if no charging lead is connected.
X Charge until the green battery status LED (13) lights
continuously.
X When charging is complete, disconnect the mains charging
adaptor (9) and store in a safe place.
Charging the unit with the 12 Vdc vehicle adaptor (fig. A
& B)
Note: The unit cannot be recharged while the 12 Vdc
accessory outlet (2) is in use or while the unit is being used
to boost/start a vehicle.
X Turn the unit on by pressing the on/off button (3). The unit
will beep once and the red power LED (11) and the battery
status LED (13) will light.
X Remove the 12 Vdc vehicle adaptor (10) from the storage
compartment (1) and plug it into the vehicle’s 12 Vdc
accessory outlet.
X Press the recharge unit button (5). The unit will beep once
and the green battery status LED (13) will flash, indicating
that the unit is charging.
X Charge until the green battery status LED (13) lights
continuously.
X When charging is complete, disconnect the 12 Vdc vehicle
adaptor (10) and return it to the storage compartment (1).
Standby mode (fig. A)
When the unit is in standby mode (not connected to a vehicle
and not charging, but with the power on), the battery status
LED (13) will light green to indicate it is ready for use. If the
battery status LED (13) lights red, the unit needs to be
charged.
Using the battery booster (fig. A)
Warning! Make sure the unit is disconnected from all charging
power sources before beginning the battery boosting procedure.
Warning! This power system is to be used only on vehicles
with dc battery systems.
Warning! Vehicles that have on-board computerized systems
may be damaged if the vehicle battery is boosted. Before battery
boosting this type of vehicle, read the vehicle owner’s manual to
confirm that external-starting assistance is advised.
Warning! Excessive engine cranking can damage the vehicle‘s
starter motor. If the engine fails to start after the recommended
number of attempts (refer to the vehicle’s owner manual),
discontinue the battery boost procedure and look for other
problems that need to be corrected.
Warning! Ensure you turn off items such as lights before you
start this procedure.
X Turn the unit on by pressing the on/off button (3). The unit
will beep once and the red power LED (11) and the battery
status LED (13) will light to indicate that it is functioning.
X Remove the 12 Vdc vehicle charging adaptor (10) from the
storage compartment (1) and plug it into the vehicle’s 12
Vdc accessory outlet.
X Press the vehicle boost button (4). The unit will beep once
and the green vehicle boost LED (4) will flash, indicating
that the vehicle battery is being charged/boosted.
Note: When connecting to a vehicle’s 12 Vdc accessory
outlet, it may be necessary to turn on the vehicles ignition to
power the accessory outlet.
X When the green vehicle boost LED (4) lights continuously
and the unit beeps, (after approximately 10 minutes), the
vehicle battery has been boosted. Turn the vehicle ignition
and crank the engine in 5-6 second bursts until engine
starts.
Note: The battery booster will not function while the unit is
recharging or while the 12 Vdc accessory outlet (2) is in use.
X After use, turn the unit off by pressing the on/off button (3)
and recharge the unit as soon as possible so that it is ready
for the next emergency.
Warning! The end of the vehicle charging adaptor will be hot
to touch during and after boosting the vehicles battery
Using the 12 Vdc portable power supply (fig. A)
This portable power supply can be used with all 12 Vdc
accessories equipped with a male accessory outlet plug
rated up to 5 amps.
Warning! Do not attempt to use the battery booster or recharge
the unit while the 12 Vdc accessory outlet (2) is in use.
X Lift the cover of the 12 Vdc accessory outlet (2).
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker BDV030 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker BDV030 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info