Manual Black Decker BDV012 (page 5 of 72) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

53611

Zoom out

Zoom in

1/72

ENGLISH

USE

Charging the unit (fig. A)

This unit is shipped in a partially charged state.

X Charge the unit before first use using the mains charging

adaptor (11) for 48 hours.

Lead-acid batteries require routine maintenance to ensure a

full charge and a long battery life. All batteries lose energy

from self-discharge over time and more rapidly at higher

temperatures. When the unit is not in use, Black & Decker

recommend that the battery is charged at least every

60 days.

X Check the battery charge level by pressing the battery

status pushbutton (4). The LED charge status display (6) will

indicate the level of battery charge. When only one red LED

lights, charge the unit.

Note: Charging the battery after each use will prolong the

battery life; frequent heavy discharges between charges

and/or overcharging will reduce battery life.

The battery can be charged using the mains charging adaptor

(11) or the 12 Vdc vehicle adaptor (12).

Charging the unit with the mains charger (fig. A)

Make sure that the ON/OFF switch (7) and the LED area light

(10) are turned off while the unit is being charged.

As charging progresses, the red LEDs will light one by one.

X Charge the unit until the green FULL LED lights.

X Continue to charge for one to two more hours.

Note: The mains charging should not be connected for more

than 60 hours.

X When charging is complete, disconnect the mains charging

adaptor (11) and store it in a safe place.

Charging the unit with the 12 Vdc vehicle adaptor

(fig. A)

Make sure that the ON/OFF switch (7) and the LED area light

(10) are turned off while the unit is being charged.

The 12 Vdc vehicle adaptor (12) does not provide a taper

charge.

Warning! While charging with the 12 Vdc vehicle adaptor (12):

X "Do not charge for more than 4 hours maximum.

X "Do not leave unattended.

To charge the unit with the 12 Vdc vehicle adaptor (12):

X Insert one end of the 12 Vdc vehicle adaptor (12) into a

12 Vdc accessory outlet on the vehicle or boat.

X Insert the other end of the 12 Vdc vehicle adaptor (12) into

the 12 Vdc accessory outlet (3) on the front of the unit.

X To check the charge status of the battery during dc

charging, disconnect the 12 Vdc vehicle adapter from the

accessory outlet and push the battery status pushbutton.

Observe the battery status LEDs. Do not charge for more

than 3 to 4 hours maximum.

X When charging is completed, remove the 12 Vdc vehicle

adaptor (12) and store it in a safe place.

Using the unit as a jump-starter (fig. A & B)

Note: A marine battery must be removed from the boat and

charged on shore. To charge it on board requires equipment

specially designed for marine use.

X Turn off the vehicles ignition and all accessories before

making any connections.

X Make sure that the units ON/OFF switch (7) is turned OFF.

X The following procedure is for a negative earth system ie

the negative battery terminal is connected to the chassis.

X Connect the positive (+) red clamp to the vehicle's positive

battery terminal.

X Connect the negative (-) black clamp to the vehicle's

chassis or a solid, non-moving, metal vehicle component or

chassis part.

Warning! Make sure that the cables are not in the path of

moving belts or the fan.

X Turn the unit's ON/OFF switch (7) to the ON position.

X Start the vehicle and crank the engine in 3 to 6 second

bursts.

If the engine doesn't start within 6 seconds let the unit's

internal battery cool for 3 minutes before making another

attempt.

X When the vehicle starts, turn the unit's ON/OFF switch (7)

to the OFF position.

X Leave the vehicle's engine running.

X Disconnect the (-) black clamp connected to the engine or

chassis first, followed by the (+) red clamp that is connected

to the battery positive (+) terminal.

X Carefully press the negative (black) jumper cable wire into

the storage channel starting at the end furthest from the

clamp.

X Clamp the negative (black) clamp onto the clamp

holder (14).

X Carefully press the positive (red) jumper cable wire into the

storage channel starting at the end furthest from the clamp.

X Clamp the positive (red) clamp onto the clamp holder(14).

X Charge the unit as soon as possible.

Using the 12 Vdc portable power supply (fig. A)

This portable power supply can be used with all 12 Vdc

accessories equipped with a male accessory outlet plug

rated up to 5 amps.

Warning! Do not attempt to use or charge the unit while the

12 Vdc accessory outlet (3) is in use.

X Lift the cover of the 12 Vdc accessory outlet (3).

X Insert the 12 Vdc plug from the appliance into the 12 Vdc

accessory outlet (3) on the top of the unit.

Warning! Do not exceed a 5A load.

X Switch on the appliance and operate as usual.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker BDV012 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,09 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker BDV012

Black Decker BDV012 User Manual - Dutch - 10 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker BDV012 Manual

Product: