53635
7
Zoom out
Zoom in
Previous page
1/104
Next page
7
ENGLISH
Language selection
The smart charger can display error message and
information in your chosen language. To alter the initial
language (default English), proceed as instructed below:
X Plug the unit into an ac source and during the
initialisation sequence, press the language button (2)
once; pressing the language button repeatedly allows
you to choose your language.
X Once a language has been selected, the smart charger
will display all messages and information in this
language.
X The language button does not need to be pressed each
time the unit is switched on; the smart charger
remembers the previous selection and defaults to this
language.
General use instructions
X Set up the unit as described in the “Connecting the
battery charger" section.
X Turn the function control knob (3) to the desired function
position.
X Plug the charger into a 230 Vac outlet.
X Connect the charger clamps to the battery.
X The digital display (1) will show ANALYSING
BATTERY, indicating that the unit is set up correctly and
ready to use.
X CHECK BATTERY CONNECTIONS will be displayed
when the unit is plugged in and there is no battery
connected to the charger or the clamps are not
connected properly.
X When the unit has completed analysing the battery, it
will begin the recharging process if the function control
knob (3) has been set to smart charge. The battery
voltage will then be displayed (for example;
CHARGING/12.5 VOLTS). As the battery charges, the
arrow on the charging gauge (6) will move indicating the
current percent of charge in the battery, from the red
zone (0 to 25% charged) toward the green zone (75-
100% charged).
X When the unit is fully charged, BATTERY IS FULLY
CHARGED will be displayed and the green status LED
light (5) will light.
X To turn the battery charger off, first disconnect the
mains cord, then disconnect the clamps (4). Observe
the “Safety Instructions" at the front of this manual when
disconnecting.
Use
The Black & Decker battery charger has a fast charge rate of
20A, 25A or 30A (depending on the model). It is designed for
charging 12V lead-acid batteries only, i.e. conventional
automotive, maintenance-free, marine, deep cycle and gel
batteries as used in cars, trucks, farm equipment, boats,
lawn mowers, garden tractors, motorcycles and various
other applications.
Autoselect technology
Select the application and the charger will do the rest.
4-Stage charging technology (fig. D)
The battery charger features 4-stage high-efficiency
charging technology using built-in microprocessor control
which ensures fast, safe and complete charging of
serviceable batteries.
Stage 1 - battery status
To make sure the battery can accept a charge, a connection
check prevents damage caused by reversed polarity.
Stage 2 - bulk charge
Charges fast by delivering pure DC current up to 80% of the
battery capacity.
Stage 3 - absorption
Avoids overcharging by slowly charging up to 100% of the
battery capacity.
Stage 4 - float mode
Maintains the battery fully charged indefinitely so it is always
ready for use.
Control panel
The following symbols are shown on the control panel:
Smart charge (fig. A)
Automatically analyses the battery and selects the best
charging rate for the battery type, size and discharge level.
Smart charge
Alternator check
Engine start
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker BDSBC30A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker BDSBC30A in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info