Manual Black Decker BDPR400 T1 (page 7 of 60) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

578621

Zoom out

Zoom in

1/60

ENGLISH

(Original instructions)

Attaching the roller head (g. B)

u Slide the handle assembly (12) into the roller head (7) en-

suring that the O-ring (13) is seated inside the roller head

(7) and the black collar (14) meets the roller head (7).

u Thread the black collar (14) onto the threads of the roller

head (7) and tighten.

Attaching a roller to the roller head (g. C)

u Lubricate the tips (15) at either end of the roller frame (16)

using petroleum jelly.

u Slide the assembled roller (8) onto the roller frame (16).

Note: Make sure the roller assembly snaps into the locking

clip on the outer end cap of the roller.

Attaching the drip tray (g. D)

The drip tray helps reduce spatter and drips when painting,

especially on ceilings.

u Clip the drip tray (9) onto the roller frame (16) so that it ts

around the roller (8).

u Rotate the drip tray to the required position.

Note: The drip tray is also helpful to prevent dripping when the

Speedy Roller

is resting on the kickstand and is not in use.

Position the drip tray under the roller.

Use

Filling with paint (g. E & F)

Note: When using the Speedy Roller

for the rst application,

it will take most of the paint in the paint reservoir to saturate

the roller cover. A second ll may be needed.

u Insert the small end of the ll tube (17) through the hole in

the bottom side of the paint can clip (18). Push gently until

it click into place.

u Place the paint can clip (18) over the edge of your paint

can.

Note: For deeper containers, t a section of 19mm inner

diameter clear tubing over the ribs of the ll tube to extend it

and clip to side of pail with ll tube can clip. Cut the bottom

end of the tubing at a slight angle. Tubing is available at most

DIY stores.

u Lubricate the top of the ll tube (17) with a small amount

of petroleum jelly.

u Hold the Speedy Roller

at a 45

angle and place the ll

valve (5) over the ll tube (17). Gently push the Speedy

Roller

down so it completely covers the ll tube.

Note: Make sure the orange ll cap cover (19) is com-

pletely covered by the shroud of the can clip.

u Very rmly pull the plunger (1) all the way back to draw

paint into Speedy Roller

ensuring you apply sufcient

pressure to maintain an adequate union between the ll

valve and ll tube.

u Lift the Speedy Roller

slowly off the ll tube.

Note: If you do not receive a complete ll the rst time, push

the plunger slowly to return paint to can and then pull the back

plunger making sure the angle is correct and the orange ll

cap cover is fully seated.

Adjusting the angle of the roller head (g. G & H)

The roller head can be adjusted to three different angles.

u Press and hold the orange head ratation button (6) on the

roller head (7).

u Rotate the rollerhead (7) to the required angle.

Note: Use straight on for general painting and 40

or 80

angles for hard to reach places or when painting close to

ceiling or edging.

Note: The handle (10) can be rotated to make it more comfort-

able when painting with an angled roller frame. To rotate

handle to desired position, loosen collar (11), adjust handle

and retighten collar (g H).

Painting with the Speedy Roller

(g. I & J)

u Begin rolling on wall and push plunger handle (1) or

squeeze trigger (2) to feed paint into the roller cover.

Note: Initial saturation of the roller may require the full amount

of paint from the rst ll. Fill Speedy Roller

as needed.

Helpful hints

u The trigger only needs to be squeezed when paint is

needed.

u If you are getting a dot pattern when painting, apply more

paint.

u If the roller is sliding on the surface, apply less paint.

u You may notice petroleum jelly within the handle. This is

necessary and will help in its operation and will not affect

the paint.

u When not in use, rest the Speedy Roller

on the kick-

stand (4) with the drip tray (9) attached and positioned

under the roller..

Returning excess paint to paint tin (g. K - M)

u Place thumb over orange ll cap cover (19).

u Pull plunger (1) back to draw excess paint from roller

frame into tube.

u Hold the Speedy Roller

at a 45

angle and place the ll

valve (5) over the ll tube (17). Gently push the Speedy

Roller

down so it completely covers the ll tube.

Note: Make sure the orange ll cap cover (19) is com-

pletely covered by the shroud of the can clip.

u Push the plunger all of the way into the tube.

u Remove the roller (8) by grasping the outer end cap (20)

and the roller frame (16) and using your thumb on the

opposite hand to push the roller off

Note: Wear disposable gloves or use a plastic bag over roller

to keep your hands clean.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker BDPR400 T1 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,02 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker BDPR400 T1

Black Decker BDPR400 T1 User Manual - Polish - 16 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker BDPR400 T1 Manual

Product: