497068
9
Zoom out
Zoom in
Previous page
1/152
Next page
9
ENGLISH
(Original instructions)
The charger may hum and become warm
while charging; this is normal and does not
indicate a problem.
Warning! Do not charge the battery at ambi-
ent temperatures below 10 °C or above 40
°C. Recommended charging temperature:
approx. 24 °C.
Low battery indicator
When the battery charge becomes low the
LED work light will begin to ash.
u The LED Flash will last 5 seconds during
Low voltage --- --- --- at this pattern..
Warning! Do not continue using the product
with its batteries in a depleted condition.
Recharge discharged batteries promptly..
High temperature indicator
When the circuit operating temperature
becomes too high the LED work light will
begin to ash.
u The LED Flash will last 5 seconds during
circuit high temperature ---- -- ---- -- ---- at
this pattern. Allow the unit to cool down
to an optimal operating temperature of
approximately 24°C.
Setting the initial starting point (g. D)
u Grasp the screwdriver as shown in gure
D.
u Press and hold in the motion control
activator (1) on the back of the tool with
the palm of your hand.
u When the LED work light (4) illuminates
the tool is ready for use.
u To reset initial starting point rst release
the motion control activator (1). Move tool
to new position, then press and hold in the
motion control activator (1) on the back of
the tool with the palm of your hand..
Operating in the forward direction
(g. E)
u Set the initial starting point.
u Rotate the tool clockwise and the screw-
driver will activate in the forward direction.
Note: The speed of the tool is determined by
the amount of rotation. .
Small rotation = slower speed.
Large rotation = Higher speed.
Operating in the reverse direction
(g. F)
u Set the initial starting point.
u Rotate the tool anti-clockwise and the
screwdriver will activate in the reverse
direction.
Note: The speed of the tool is determined by
the amount of rotation. .
Small rotation = slower speed.
Large rotation = Higher speed.
LED work light
The LED work light (4) is activated automati-
cally when the motion control activator (1) is
depressed.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker BDCS36G at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker BDCS36G in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info