709546

Black Decker BDCR18 Manual

7
Zoom out
Zoom in
Previous page
1/88
Next page
7
ENGLISH
(Original instructions)
Fitting the saw blade (g. A)
u Hold the tool away from the body.
u Open the blade clamp release lever (4) to the full open
position.
u Insert blade shank from the front.
u Close blade clamp release lever (4). Check to make sure
the blade (5) is clamped securley.
Note: The blade can be installed with the teeth up to assist in
ush cutting (g. G).
Removing the saw blade
Warning! Do not touch the blade immediately after use. Used
saw blades may be hot.
u Open the blade clamp release lever (4) to the full open
position.
u Remove the blade.
Lock-off button
The tool is equipped with a switch lock-off feature to prevent
unintentional operation.
u To switch the tool on, press the lock-off button (2) then
squeeze the on/off switch (1).
u Releasing the on/off switch (1) turns the tool off.
Fitting and removing the battery (g. B & C)
u To t the battery (6), line it up with the receptacle on the
tool. Slide the battery into the receptacle and push until
the battery snaps into place (g. B).
u To remove the battery (6), push the battery release button
(7) while at the same time pulling the battery out of the
receptacle on the tool (g. C).
Use
Warning! Let the tool work at its own pace. Do not overload.
Charging the battery (Fig. D)
The battery needs to be charged before rst use and whenev-
er it fails to produce sufcient power on jobs that were easily
done before. The battery may become warm while charging;
this is normal and does not indicate a problem.
Warning! Do not charge the battery at ambient tempera-
tures below 10
°
C or above 40
°
C. Recommended charging
temperature: approx. 24
°
C.
Note: The charger will not charge a battery if the cell
temperature is below approximately 10
°
C or above 40
°
C.
The battery should be left in the charger and the charger
will begin to charge automatically when the cell tempera-
ture warms up or cools down.
u To charge the battery (6), insert it into the charger (10).
The battery will only t into the charger in one way. Do
not force. Be sure that the battery is fully seated in the
charger.
u Plug in the charger and switch on at the mains.
The green charging indicator will ash.
The charge is complete when the green charging indicator
switches to continuously on. The charger and the battery can
be left connected indenitely. The green charging indicator will
ash as the charger occasionally tops up the battery charge.
u Charge discharged batteries within 1 week. Battery life will
be greatly diminished if stored in a discharged state.
Leaving the battery in the charger
The charger and battery pack can be left connected with the
green charging indicator glowing indenitely. The charger will
keep the battery pack fresh and fully charged.
Switching on and off
u To switch the tool on, press the lock-off button (2) then
squeeze the on/off switch (1).
u To switch the tool off, release the on/off switch (1).
Sawing (g. E)
u Always hold the tool with both hands (g. E).
u Let the blade (5) run freely for a few seconds before start-
ing the cut.
u Apply only a gentle pressure to the tool while performing
the cut.
u If possible, work with the shoe (3) pressed against the
workpiece. This will improve tool control and reduce tool
vibration, as well as prevent the blade from being dam-
aged.
Hints for optimum use
Sawing wood (g. F)
u Clamp the workpiece securely and remove all nails and
metal objects.
u Holding the tool with both hands, work with the shoe (3)
pressed against the workpiece.
Flush cutting (g. G)
The compact design of the reciprocating saw motor housing
and pivoting shoe (3) permit close cutting to oors, corners
and other difcult areas.
To maximize ush cutting capabilities:
u Insert the blade shaft into the blade clamp with the teeth of
the blade facing up.
u Adjust the angle of the handle on the tool so you are as
close to the work surface as possible.
Sawing metal (g. H)
u Use a saw blade suitable for sawing metal. Use a ne-
tooth saw blade for ferrous metals and a coarser saw
blade for non-ferrous metals.
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker BDCR18 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker BDCR18 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info