709458
7
Zoom out
Zoom in
Previous page
1/108
Next page
ENGLISH
(Original instructions)
7
u Insert the bit shaft (10) and release the chuck collar
(3).
u The bit is locked in place.
Removing a drill bit or screwdriver bit
u Grasp the chuck collar (3) and pull away from the front
of the tool.
u Remove the bit (10) and release the chuck collar (3).
Bit holder
A bit holder (6) slot is built into the area on the top of the
tool.
Use
Warning! Let the tool work at its own pace. Do not
overload.
Charging the battery (g. A)
The battery needs to be charged before rst use and
whenever it fails to produce sufcient power on jobs that
were easily done before. The battery may become warm
while charging; this is normal and does not indicate a
problem.
Warning! Do not charge the battery at ambient tem-
peratures below 10 °C or above 40 °C. Recommended
charging temperature: approx. 24 °C.
Note: The charger will not charge a battery if the cell
temperature is below approximately 10 °C or above
40 °C.
The battery should be left in the charger and the
charger will begin to charge automatically when the
cell temperature warms up or cools down.
u To charge the battery (8), insert it into the charger (7).
The battery will only t into the charger in one way. Do
not force. Be sure that the battery is fully seated in the
charger.
u Plug in the charger and switch on at the mains.
The green charging indicator will blink indicating the bat-
tery is being charged.
The charge is complete when the green charging indicator
switches to continuously on. The charger and the battery
can be left connected indenitely. The green charging
indicator will switch on as the charger occasionally tops up
the battery charge.
u Charge discharged batteries within 1 week. Battery
life will be greatly diminished if stored in a discharged
state.
Leaving the battery in the charger
The charger and battery pack can be left connected with
the green charging indicator glowing indenitely. The
charger will keep the battery pack fresh and fully charged.
Variable speed switch on/off (g. D)
u To switch the tool on, press the variable speed switch
(1).
u To switch the tool off, release the variable speed
switch (1).
Note: Your tool is equipped with a brake. The chuck will
stop as soon as the variable speed switch is fully released.
u The variable speed switch (1) enables you to select
the best speed for a particular application.
u The more you press the variable speed switch (1), the
faster the tool will operate.
u The more you press the variable speed switch (1), the
faster the tool will operate.
u Use lower speeds for starting holes without a centre
punch, drtilling in metals or plastics, or driving screws.
Note: Continuous use in variable speed mode is not
recommended. It may damage the switch and should be
avoided.
Selecting the direction of rotation (g. D)
For drilling and for tightening screws, use forward
(clockwise) rotation. For loosening screws or removing a
jammed drill bit, use reverse (counterclockwise) rotation.
u To select forward rotation, release the variable speed
switch (1) depress the forward/reverse slider (2) on
the right hand side of the tool.
u To select reverse rotation, release the variable speed
switch (1) depress the forward/reverse slider (2) on
the left hand side of the tool.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker BDCIM18 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker BDCIM18 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info