709549
6
Zoom out
Zoom in
Previous page
1/84
Next page
6
ENGLISH
(Original instructions)
u Do not expose the battery to water.
u Do not store in locations where the temperature may
exceed 40 °C.
u Charge only at ambient temperatures between 10 °C and
40 °C.
u Charge only using the charger provided with the tool.
u When disposing of batteries, follow the instructions given
in the section "Protecting the environment".
Do not attempt to charge damaged batteries.
Chargers
u Use your BLACK+DECKER charger only to charge
the battery in the tool with which it was supplied. Other
batteries could burst, causing personal injury and damage.
u Never attempt to charge non-rechargeable batteries.
u Have defective cords replaced immediately.
u Do not expose the charger to water.
u Do not open the charger.
u Do not probe the charger.
$
The charger is intended for indoor use only.
Read the instruction manual before use.
Labels on tool
The following pictograms along with the date code are shown
on the tool:
Warning! To reduce the risk of injury, the user
must read the instruction manual.
Wear a dust mask.
Electrical safety
#
Your charger is double insulated; therefore no
earth wire is required. Always check that the
mains voltage corresponds to the voltage on the
rating plate. Never attempt to replace the charger
unit with a regular mains plug.
u If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
Features
This tool includes some or all of the following features.
1. On/off switch
2. Dust collection cassette
3. Sanding base
4. Finger attachment
5. Battery
Accessories
The accessories supplied with your sander depend upon the
model that you have purchased. All the accessories listed
below are available in our range. If you require an accessory
that is listed below but is not supplied with your sander please
visit our website at www.blackanddecker.eu.
The performance of your tool depends on the accessory used.
BLACK+DECKER accessories are engineered to high quality
standards and designed to enhance the performance of your
tool. By using these accessories you will get the very best
from your tool.
Item Description
Detail nger.
For small hard-to-reach areas. The detail
nger can be used for light sanding and
for sanding into corners.
(Part Number - X32214-XJ)
240 grit sanding mesh.
For a ne nish for large detail sanding.
(Part Number - X39132-XJ)
120 grit sanding mesh.
For a medium nish for large detail
sanding.
(Part Number - X39127-XJ)
80 grit sanding mesh.
For a coarse nish for large detail
sanding.
(Part Number - X39122-XJ)
240 grit large detail sanding sheet
with two replacement tips.
For a ne nish for large detail sanding.
(Part Number - X31019-XJ)
120 grit large detail sanding sheet
with two replacement tips.
For a medium nish for large detail
sanding.
(Part Number - X31009-XJ)
60 grit large detail sanding sheet with
two replacement tips.
For a coarse nish for large detail
sanding.
(Part Number - X31039-XJ)
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker BDCDS18 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker BDCDS18 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info