661441
6
Zoom out
Zoom in
Previous page
1/108
Next page
ENGLISH
(Original instructions)
6
Additional safety instructions for batteries and
chargers (Not provided with the tool)
Batteries
u Never attempt to open for any reason.
u Do not expose the battery to water.
u Do not store in locations where the temperature may
exceed 40 °C.
u Charge only at ambient temperatures between 10 °C
and 40 °C.
u Charge only using the charger provided with the tool.
u When disposing of batteries, follow the instructions
given in the section "Protecting the environment".
p
Do not attempt to charge damaged batteries.
Chargers
u Use your BLACK+DECKER charger only to charge
the battery in the tool with which it was supplied. Other
batteries could burst, causing personal injury and
damage.
u Never attempt to charge non-rechargeable batteries.
u Have defective cords replaced immediately.
u Do not expose the charger to water.
u Do not open the charger.
u Do not probe the charger.
$
The charger is intended for indoor use only.
+
Read the instruction manual before use.
Electrical safety
#
Your charger is double insulated; therefore no
earth wire is required. Always check that the
mains voltage corresponds to the voltage on
the rating plate. Never attempt to replace the
charger unit with a regular mains plug.
u If the supply cord is damaged, it must be replaced by
the manufacturer or an authorised BLACK+DECKER
Service Centre in order to avoid a hazard.
Features
This tool includes some or all of the following features.
1. Variable speed switch
2. Forward/reverse slider
3. Chuck
4. Torque adjustment collar
5. Battery (not included, sold separately)
6. Bit holder
Fig. A (Not included, sold separately)
5. Battery
7. Charger
8. Charger indicator
Assembly
Warning! Before assembly, remove the battery from the
tool.
Fitting and removing the battery (g. B)
u To t the battery (5), line it up with the receptacle on
the tool. Slide the battery into the receptacle and push
until the battery snaps into place.
u To remove the battery, push the release button (9)
while at the same time pulling the battery out of the
receptacle.
Fitting and removing a drill bit or screwdriver
bit (g. C)
This tool is tted with a keyless chuck to allow for an easy
exchange of bits.
u Grasp the rear half of the chuck (3) with one hand
and use your other hand to rotate the front half in the
counterclockwise direction, as viewed from the chuck
end.
u Insert the bit shaft (10) into the chuck.
u Firmly tighten the chuck by holding the rear half of the
chuck and rotating the front portion in the clockwise
direction as viewed from the chuck end.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker BDCDD18 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker BDCDD18 in the language / languages: All languages as an attachment in your email.

The manual is 1,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info