Manual Black Decker BCD003 (page 7 of 88) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

709448

Zoom out

Zoom in

1/88

ENGLISH

(Original instructions)

u The battery pack should be recharged when it fails to

produce sufcient power on jobs which were easily

done previously. DO NOT CONTINUE to use under these

conditions. Follow the charging procedure. You may also

charge a partially used pack whenever you desire with no

adverse effect on the battery pack.

u Foreign materials of a conductive nature such as, but

not limited to, grinding dust, metal chips, steel wool,

aluminum foil, or any buildup of metallic particles

should be kept away from charger cavities. Unplug the

charger before attempting to clean.

u Do not freeze or immerse the charger in water or any

other liquid.

Installing and removing the battery pack from the

tool (g. B)

Warning! Make certain the lock-off button (2) is engaged to

prevent switch actuation before removing or installing battery.

To install battery pack:

u Insert battery pack (7) into tool, until an audible click is

heard (g. B)

Removing the battery pack from the tool (g. C)

u Depress the battery release button (8) as shown in (g. C)

and pull battery pack out of tool.

Operating Instructions

Trigger switch & reversing button (g. D)

u The drill is turned ON and OFF by pulling and releasing

the trigger switch (1). The farther the trigger is depressed,

the higher the speed of the drill.

u A forward/reverse control button (2) determines the direc-

tion of the tool and also serves as a lock off button.

u To select forward rotation, release the trigger switch and

depress the forward/reverse control button to the left.

u To select reverse, depress the forward/reverse control

button the opposite direction.

Note: The center position of the control button locks the tool

in the off position. When changing the position of the control

button, be sure the trigger is released.

Torque control (g.E)

This tool is tted with a torque adjustment collar (3) to select

the operating mode and to set the torque for tightening

screws. Large screws and hard workpiece materials require

a higher torque setting than small screws and soft workpiece

materials.

u For drilling in wood, metal and plastics, set the collar to

the drilling position symbol

u For screwdriving, set the collar to the desired setting. If you

do not yet know the appropriate setting, proceed as

follows:

u Set the collar to the lowest torque setting.

u Tighten the rst screw.

u If the clutch ratchets before the desired result is achieved,

increase the collar setting and continue tightening the

screw. Repeat until you reach the correct setting. Use this

setting for the remaining screws.

Keyless chuck (g. F)

Warning! Make certain the lock-off button (2) is engaged to

prevent switch actuation before installing or removing acces-

sories.

To insert a drill bit or other accessory:

u Grasp the rear half of the chuck (4) with one hand and use

your other hand to rotate the front half in the counterclock-

wise direction, as viewed from the chuck end.

u Insert the bit or other accessory fully into the chuck, and

tighten securely by holding the rear half of the chuck and

rotating the front portion in the clockwise direction as

viewed from the chuck end.

Warning! Do not attempt to tighten drill bits (or any other ac-

cessory) by gripping the front part of the chuck and turning the

tool on. Damage to the chuck and personal injury may occur

when changing accessories.

Dual range gearing (Figure G)

The dual range feature of your drill allows you to shift gears

for greater versatility. To select low speed, high torque setting

(position 1), turn tool off and permit to stop. Slide gear shifter

button (5) away from the chuck. To select the high speed, low

torque setting (position 2), turn tool off and permit to stop.

Slide gear shifter button towards the chuck.

Note: Do not change gears when tool is running. If you are

having trouble changing gears, make sure that the dual range

gear button is either completely pushed forward or completely

pushed back.

Drilling/screwdriving

u Select forward or reverse rotation using the forward/re-

verse slider (2).

u To switch the tool on, press the switch (1). The tool speed

depends on how far you press the switch.

u To switch the tool off, release the switch.

Hints for optimum use

Drilling

u Use sharp drill bits only.

u Support and secure work properly, as instructed in the

Safety Instructions.

u Use appropriate and required safety equipment, as

instructed in the Safety Instructions.

u Secure and maintain work area, as instructed in the

Safety Instructions.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker BCD003 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,6 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker BCD003 Manual

Product: