580854
6
Zoom out
Zoom in
Previous page
1/72
Next page
6
ENGLISH
Adjusting the saw blade support roller
(fi g. A & B)
Loosen the screw (9).
Push the shoe plate (4) forward until the saw
blade support roller (5) touches the back edge
of the saw blade (7).
Tighten the screw (9).
Fitting and removing the saw blade (fi g. C)
Before fi tting or removing the saw blade (7) the
saw blade support roller (5) must be adjusted
to the rear position so that it does not contact
the blade.
Loosen (do not remove) the two screws (6).
Hold the saw blade (7) with the teeth facing
forward.
Insert the shank of the saw blade (7) into the
blade holder (8) as far as it will go.
Slightly tighten the two screws (6) alternately
to position the blade, then fully tighten the two
screws (6).
Adjust the saw blade support roller (5) as
described above.
To remove the saw blade (7), turn both screws
(6) one turn counter-clockwise.
Saw blade storage (fi g. D)
Saw blades can be stored in the storage
compartment (3) at the rear of the tool.
Open the cover of the saw blade storage
compartment (3).
Remove or store saw blades (7) in the storage
compartment. (3).
Close the cover of the saw blade storage
compartment (3) and make sure that it is
latched closed.
Cut line blower (fi g. E)
To aid visibility when cutting, your jigsaw is
equipped with a cut line blower (10) which will
keep the work area clear of dust as you saw.
Residual risks
Additional residual risks may arise when using the
tool which may not be included in the enclosed
safety warnings. These risks can arise from
misuse, prolonged use etc.
Even with the application of the relevant safety
regulations and the implementation of safety
devices, certain residual risks cannot be avoided.
These include:
Injuries caused by touching any rotating/
moving parts.
Vibration
The declared vibration emission values stated in
the technical data and the declaration of conformity
have been measured in accordance with
a standard test method provided by EN 60745 and
may be used for comparing one tool with another.
The declared vibration emission value may also be
used in a preliminary assessment of exposure.
Warning! The vibration emission value during
actual use of the power tool can differ from the
declared value depending on the ways in which
the tool is used. The vibration level may increase
above the level stated.
When assessing vibration exposure to determine
safety measures required by 2002/44/EC to
protect persons regularly using power tools in
employment, an estimation of vibration exposure
should consider, the actual conditions of use and
the way the tool is used, including taking account
of all parts of the operating cycle such as the times
when the tool is switched off and when it is running
idle in addition to the trigger time.
Labels on tools
Warning! To reduce the risk of injury, the
user must read the instruction manual.
Electrical safety
This tool is double insulated; therefore
no earth wire is required. Always check
that the power supply corresponds to the
voltage on the rating plate.
If the supply cord is damaged, it must be
replaced by the manufacturer or an authorised
Black & Decker Service Centre in order to
avoid a hazard.
Features
1. On/off switch
2. Lock-on button
3. Saw blade storage compartment
4. Shoe plate
5. Saw blade support roller
Assembly
Warning! Before attempting any of the following
operations, make sure that the tool is switched
off and unplugged and that the saw blade has
stopped. Used saw blades may be hot.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker AST7XC T2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker AST7XC T2 in the language / languages: English, German, French, Polish, Turkish as an attachment in your email.

The manual is 1,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info