53559
5
Zoom out
Zoom in
Previous page
1/52
Next page
5
ENGLISH
Electrical safety
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
Additional safety instructions for angle grinders
Wear safety glasses or goggles when operating this tool.
Wear ear protection when operating this tool.
Wear gloves when operating this tool.
Do not cut or grind light metal with a magnesium content
exceeding 80%, since this type of metal is flammable.
Only use grinding and cutting discs and other accessories
recommended in this manual.
Make sure that the maximum speed of the grinding or
cutting disc exceeds the no-load speed of the tool.
Do not cut workpieces requiring a maximum depth of cut
exceeding that of the cutting disc.
Never use the tool without the guard, except for sanding.
Do not exert side pressure on the grinding or cutting disc.
Features
This tool includes some or all of the following features.
1. On/off switch
2. Lock-off button
3. Side handle
4. Spindle lock
5. Guard
Assembly
Warning! Make sure that the tool is switched off and unplugged.
Fitting and removing the guard (fig. A)
Fitting
Place the tool on a table, with the spindle (6) facing up.
Hold the guard (5) over the tool as shown.
Align the holes in the adjusting plate (7) with the screw
holes (8).
Press the guard down and insert the screws (9) into the
holes.
Tighten the screws.
Removing
Remove the screws (9).
Take the guard off the tool.
Warning! Never use the tool without the guard.
Adjusting the guard (fig. B)
The guard can be rotated 180°.
Slacken the screws (9) and the nut (10).
Rotate the guard as required.
Re-tighten the screws and the nut.
Fitting the side handle
Screw the side handle (3) into one of the mounting holes
in the tool.
Warning! Always use the side handle.
Fitting and removing grinding or cutting discs (fig. C - F)
Always use the correct type of disc for your application.
Always use discs with the correct diameter and bore size
(see technical data). The maximum thickness for grinding discs
is 6 mm, for cutting discs 3.5 mm.
Fitting
Fit the guard as described above.
Place the inner flange (11) onto the spindle (6) as shown
(fig. C). Make sure that the flange is correctly located on
the flat sides of the spindle.
Place the disc (12) onto the spindle (6) as shown (fig. D).
If the disc has a raised centre (13), make sure that the
raised centre faces the inner flange.
Make sure that the disc locates correctly on the inner flange.
Place the outer flange (14) onto the spindle. When fitting
a grinding disc, the raised centre on the outer flange must
face towards the disc (A in fig. E). When fitting a cutting
disc, the raised centre on the outer flange must face away
from the disc (B in fig. E).
Keep the spindle lock (4) depressed and tighten the outer
flange using the two-pin spanner (15) (fig. F).
Removing
Keep the spindle lock (4) depressed and loosen the outer
flange (14) using the two-pin spanner (15) (fig. F).
Remove the outer flange (14) and the disc (12).
Use
Warning! Let the tool work at its own pace.
Do not overload.
Carefully guide the cable in order to avoid accidentally
cutting it.
Be prepared for a stream of sparks when the grinding or
cutting disc touches the workpiece.
Always position the tool in such a way that the guard
provides optimum protection from the grinding or cutting
disc.
Switching on and off
To switch the tool on, press the lock-off button (2) and
subsequently press the on/off switch (1).
To switch the tool off, release the on/off switch (1).
Warning! Do not switch the tool off while under load.
Untitled-1 31-07-2003, 13:215
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker AST20XC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker AST20XC in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info