383811
4
Zoom out
Zoom in
Previous page
1/44
Next page
4
Electrical safety
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
Features
This tool includes some or all of the following features.
1. On/off switch
2. Lock-on button
3. Dust shroud
4. Blade support roller
5. Shoe plate
6. Dust extraction opening
7. Allen key
Assembly
Warning! Before attempting any of the following operations,
make sure that the tool is switched off and unplugged and
that the saw blade has stopped.
Fitting the saw blade (fig. A)
Remove the dust shroud (3).
Loosen the screw (8) using the Allen key provided.
Hold the saw blade (9) as shown, with the teeth facing
forward.
Insert the shank of the saw blade into the blade holder (10)
as far as it will go.
Tighten the screw (8).
Adjust the blade support roller as described below.
Adjusting the blade support roller (fig. B & C)
Loosen the screws (11).
Push the blade support roller (4) forward until it touches
the saw blade.
Tighten the screws (11).
Make sure that the shoe plate is adjusted correctly.
See below.
Connecting a vacuum cleaner to the tool (fig. D)
An adaptor is required to connect a vacuum cleaner or dust
extractor to the tool. The adaptor can be purchased from your
local Black & Decker retailer.
Push the adaptor (12) into the opening (6).
Connect the vacuum cleaner hose (13) to the adaptor.
Make sure that the dust shroud (3) is fitted.
Use
Adjusting the shoe plate for bevel cuts (fig. E)
The shoe plate can be set to a left or right bevel angle of up to
45°.
Loosen the screws (11).
Pull the shoe plate (5) forward, set it to the required angle
and push it back into place. You can use the scale or a
protractor to check the angle.
Tighten the screws (11).
Make sure that the blade support roller is adjusted correctly.
To reset the shoe plate for straight cuts:
Loosen the screws (11).
Pull the shoe plate forward and set it to an angle of
approx. 0°.
Make sure that the blade support roller is adjusted correctly.
Push the shoe plate backward and tighten the screws (11).
Use a square to check the angle.
Switching on and off
To switch the tool on, press the on/off switch (1).
For continuous operation, press the lock-on button (2) and
release the on/off switch.
To switch the tool off, release the on/off switch.
To switch the tool off when in continuous operation, press
the on/off switch once more and release it.
Hints for optimum use
Sawing laminates
As the saw blade cuts on the upward stroke, splintering may
occur on the surface closest to the shoe plate.
Use a fine-tooth saw blade.
Saw from the back surface of the workpiece.
To minimise splintering, clamp a piece of scrap wood or
hardboard to both sides of the workpiece and saw
through this sandwich.
Sawing metal
Be aware that sawing metal takes much more time than
sawing wood.
Use a saw blade suitable for sawing metal.
When cutting thin sheet metal, clamp a piece of scrap
wood to the back surface of the workpiece and cut
through this sandwich.
Spread a film of oil along the intended line of cut.
Accessories
The performance of your tool depends on the accessory used.
Black & Decker and Piranha accessories are engineered to
high quality standards and designed to enhance the performance
of your tool. By using these accessories you will get the very
best from your tool.
ENGLISH
AST7EUR.PM65 19-04-2002, 12:334
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker ast 7 xcw at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker ast 7 xcw in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info