Manual Black Decker ASL148 (page 6 of 100) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

472962

Zoom out

Zoom in

1/100

ENGLISH

(Original instructions)

Fitting and removing a drill bit or screwdriver bit

(g. D)

This tool is tted with a keyless chuck to allow for an easy

exchange of bits.

u Lock the tool by setting the forward/reverse slider (2) to

the centre position.

u Open the chuck by turning it (3) with one hand while

holding the tool with the other.

u Insert the bit shaft (13) into the chuck.

u Firmly tighten the chuck by turning it (3) with one hand

while holding the tool with the other.

Use

Warning! Let the tool work at its own pace. Do not overload.

Charging the battery (g. A)

The battery needs to be charged before rst use and

whenever it fails to produce sufcient power on jobs that were

easily done before. The battery may become warm while

charging; this is normal and does not indicate a problem.

Warning! Do not charge the battery at ambient temperatures

below 4 °C or above 40 °C. Recommended charging

temperature: approx. 24 °C.

Note: The charger will not charge a battery if the cell

temperature is below approximately 0 °C or above 40 °C.

The battery should be left in the charger and the charger

will begin to charge automatically when the cell

temperature warms up or cools down.

u To charge the battery (5), insert it into the charger (9). The

battery will only t into the charger in one way. Do not

force. Be sure that the battery is fully seated in the

charger.

u Plug in the charger and switch on at the mains.

The charging indicator (10) will ash green continuously

(slowly).

The charge is complete when the charging indicator (10) lights

green continuously. The charger and the battery can be left

connected indenitely with the LED illuminated. The LED will

change to ashing green (charging) state as the charger

occasionally tops up the battery charge. The charging

indicator (10) will be lit as long as the battery is connected to

the plugged-in charger.

u Charge discharged batteries within 1 week. Battery life will

be greatly diminished if stored in a discharged state.

Leaving the battery in the charger

The charger and battery pack can be left connected with the

LED glowing indenitely. The charger will keep the battery

pack fresh and fully charged.

Charger diagnostics

If the charger detects a weak or damaged battery, the

charging indicator (10) will ash red at a fast rate. Proceed as

follows:

u Re-insert the battery (5).

u If the charging indicators continues ashing red at a fast

rate, use a different battery to determine if the charging

process works properly.

u If the replaced battery charges correctly, the original

battery is defective and should be returned to a service

centre for recycling.

u If the new battery gives the same indication as the original

battery, take the charger to be tested at an authorised

services centre.

Note: It may take as long as 60 minutes to determine that

the battery is defective. If the battery is too hot or too

cold, the LED will alternately blink red, fast and slow, one

ash at each speed and repeat.

Selecting the direction of rotation (g. F)

For drilling and for tightening screws, use forward (clockwise)

rotation. For loosening screws or removing a jammed drill bit,

use reverse (counterclockwise) rotation.

u To select forward rotation, push the forward/reverse slider

(2) to the left.

u To select reverse rotation, push the forward/reverse slider

to the right.

u To lock the tool, set the forward/reverse slider into the

centre position.

Selecting the torque (g. E)

This tool is tted with a unique collar to set the torque for

various screwdriving and drilling applications. Large screws

and hard workpiece materials require a higher torque setting

than small screws and soft workpiece materials. The collar

has a wide range of settings represented by symbols to suit

your application. For the denition of the symbol refer to the

listing below.

u For drilling in wood, metal and plastics, set the torque

adjustment collar (4) to the symbol corresponding to the

appropriate drilling application.

u For screwdriving, set the collar to the desired setting. If

you do not yet know the appropriate setting, proceed as

follows:

- Set the torque adjustment collar (4) to the lowest torque

setting.

- Tighten the rst screw.

- If the clutch ratchets before the desired result is

achieved, increase the collar setting and continue

tightening the screw. Repeat until you reach the correct

setting. Use this setting for the remaining screws.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker ASL148 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 8,66 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker ASL148 Manual

Product: