Manual Black Decker ASI500 TH2 (page 7 of 12) (English)

581290

Zoom out

Zoom in

1/12

 Plug the AC charger (13) into the mains power supply.

 The LED (15) on the AC charger (13) will indicate the

level of charging. Red, unit charging, Green, unit

charged.

 When fully charged, remove the AC charger from the

mains and remove the jack plug from the unit.

Note: Store your AC charger in a safe place for later use.

Residual risks

Additional residual risks may arise when using the tool which

may not be included in the enclosed safety warnings. These

risks can arise from misuse, prolonged use etc.

Even with the application of the relevant safety regulations

and the implementation of safety devices, certain residual

risks cannot be avoided. These include:

 Injuries caused by touching any rotating/moving parts.

 Injuries caused when changing any parts, blades or

accessories.

 Injuries caused by prolonged use of a tool. When using

any tool for prolonged periods make sure you take

regular breaks.

 Impairment of hearing.

 Health hazards caused by breathing dust developed

when using your tool (example:- working with wood,

especially oak, beech and MDF).

Use

Hose and cord storage (fig. B - D)

 Wrap the 12 Vdc cord (17) around the base of the unit

and locate the 12 Vdc adapter (8) into its storage

location (16) as shown in fig. B and then rotate through

90° to secure in place.

 The air hose (5) is located in a storage channel (26)

around the top of the unit (fig. C), make sure the hose is

snapped into the retaining clips and the lever (19) is in

the up position (fig. D).

 The high-volume hose (7) is stored in a storage channel

around the centre of the unit and snaps into position at

both ends. The accessories (14) are stored on the front

of the unit.

Fitting the accessories (fig. D, G - I)

Your inflator is supplied with the standard tapered nozzles

and the needle inflator nozzle, these are stored on the front

of the unit (14).

 To use the universal valve adaptor (6), make sure that

the lever (19) is in the up position.

 Place the universal valve adapter (6) over the stem of

the inflation needle or tapered nozzle (fig.D).

 Press the lever (19) on the universal valve adapter (6)

down to lock it in place.

 Place the inflation needle or tapered nozzle into the item

to be inflated.

Note: Always make sure that the lever is in the up position

when not in use. Operate your inflator only with the universal

valve adaptor or with the included nozzles.

Note: Make sure that the universal valve adapter is firmly

locked in place before turning the inflator on.

Your inflator is supplied with a high volume adaptor (24).

This is stored on the front of the unit (fig. G).

 To use the high volume adaptor (24), remove it from the

high volume inflate connection (10).

 Remove the high volume hose (7) from the storage

location.

 Remove the tapered nozzle (18) from the end of the

high volume hose (7).

 Fit the high volume adaptor (24) to the end of the high

volume hose (fig. H).

Many inflatables have an internal flap that prevents air loss

during inflation, especially air mattresses. Unless this flap is

displaced by the nozzle the inflatable will not inflate. Push

the nozzle firmly into the valve to make sure that you push

this flap out of the way.

Warning! Excessive air pressure may cause a hazardous

risk of bursting or personal injury. Check the manufacturer's

maximum pressure rating for items being inflated.

Note: If the pressure rating for the item being inflated is

above 100 PSI / 6.89 BAR / 689 KPA, note that the maximum

run time is 10 minutes, leave to rest for 20 minutes before re-

use.

Operating the inflator (fig. E)

Warning! Do not operate the inflator when the car engine is

running.

Note: Make sure that your 12 Vdc accessory socket is live.

On some vehicles the accessory socket may only become

live when the ignition key is in the accessory position.

To power the display from the 12 Vdc adapter:

 Always fully extend the 12 Vdc cord before each use.

 Connect the 12 Vdc adapter (8) into your vehicles

12 Vdc accessory socket.

 Switch the main power switch (1) to the inflate

position (c) to power-up the LCD.

To power the LCD from the internal battery (cordless

operation):

 Switch the main power switch (1) to the inflate position

Warning! Do not leave the inflator running unattended. It

could burst tyres or other items.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker ASI500 TH2 in the language / languages: English as an attachment in your email.

The manual is 0,83 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Black Decker ASI500 TH2

Black Decker ASI500 TH2 User Manual - English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish - 94 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Black Decker ASI500 TH2 Manual

Product: