53548
3
Zoom out
Zoom in
Previous page
1/7
Next page
10
Maintenance
Your Elu attachment has been designed to operate over a long period of
time with a minimum of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
Remove dust and chips using compressed air.
Lubrication
Your attachment requires no additional lubrication.
Cleaning
Regularly clean the attachment with a soft cloth.
Elu After-Sales service
All Elu products are thoroughly tested before leaving the factory. However,
if the product needs repair, please contact your dealer or the Elu Head
Office for the address of the nearest Elu authorized repair agent (please
refer to the back of this manual).
Unwanted products and the environment
Take your attachment to an Elu authorized repair agent where it will be
disposed of in an environmentally safe way.
GUARANTEE
• 30 DAY NO RISK SATISFACTION GUARANTEE •
If you are not completely satisfied with the performance of your Elu
tool, simply return it within 30 days, complete as purchased, to your
Elu dealer, for a full refund or exchange. Proof of purchase must be
provided.
• ONE YEAR FULL WARRANTY •
If your Elu product becomes defective due to faulty materials or
workmanship within 12 months from the date of purchase, we
guarantee to replace all defective parts free of charge or, at our
discretion, replace the unit free of charge provided that:
The product has not been misused.
Repairs have not been attempted by unauthorized persons.
Proof of purchase date is provided.
This guarantee is offered as an extra benefit and is additional to
consumers statutory rights.
en - 3
ENGLISH
Instructions for use
Always observe the safety instructions and applicable
regulations.
For short workpieces, always use a push stick.
Prior to operation:
Check that the Power Tool is mounted as described above.
Check that all guards and fences are in perfect working order and
mounted correctly.
Connect a dust extractor.
Set the required planing depth (refer to the instruction manual of your
planer).
Switching ON and OFF (fig. A)
Press the ON/OFF-switch of your planer.
Lock the Power Tool in ON-position using the switch strap (1) or
wedge (1a for HH40).
To stop the tool, remove the switch strap or wedge.
When using a no-volt release switch (option)
Press the ON/OFF-switch of your planer.
Lock the Power Tool in ON-position.
Lift the plug cover and plug in the Power Tool behind the connector.
Connect the machining table to the mains by plugging an extension
cable into the connector of the no-volt release switch.
To switch the planer ON, press the green button of the no-volt release
switch.
To switch the planer OFF, press the red button of the no-volt release
switch.
HH40E
On electronic planers, the brake will not operate if switched off via the no-
volt release switch.
Surfacing
Surfacing at 90° (fig. A2)
Press the material firmly against the parallel fence and on the planer
shoe and feed it against the rotating cutter block.
The blade guard will yield and return to its original position
automatically.
Always work with closed hands.
Keep your hands away from the rotating cutter block!
Surfacing at 45° (fig. H)
Reverse the parallel fence (13) as described above.
Proceed as described for surfacing at 90°.
Thicknessing (fig. I)
Set the thicknessing table (7) to the required height allowing for the
chip clearance.
Place the workpiece on the thicknessing table (7) and feed the
workpiece smoothly under the guide blade (32) and parallel to the
planing shoe.
At the outfeed side, pull the workpiece out holding it down.
In case of excessive resistance, reduce the planing depth and check
the blades.
The sliding chip fence (33) can be opened for a better view of the
thicknessing operation.
Slacken the screw (34) and slide the chip fence (33) in the direction of
the arrow (35).
Wear safety goggles during this operation.
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Black Decker ADE80 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Black Decker ADE80 in the language / languages: English as an attachment in your email.

The manual is 0,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info