669273

Bissell Hydro Clean Pro Heat Complete 1474J Manual

10
Zoom out
Zoom in
Previous page
1/11
Next page
D
Care,
Maintenance & Storage
D-1 Machine care
1. Push power and wet clean buttons off.
Unplug cleaner.
2. Open Quick Release™ hose door and
remove collection tank by lifting straight up
using tank handle.
3. Remove top lid from collection tank, rinse
and air dry.
4. Empty dirty water into a sink, toilet
or outside by pouring dirt water out
from corner of tank. Rinse inside of
collection tank.
5. Remove cleaning mode selector by
turning to “REMOVE” and pulling straight
out.
6. Once cleaning mode selector is removed,
remove water filtration tower by lifting up
and rotating clockwise so front of tower is
facing side of collection tank. Then pull up
and out of collection tank.
7. Rinse collection tank, cleaning mode
selector and water filtration tower. Allow
to air dry completely before replacing
water filtration tower and cleaning mode
selector back into collection tank.
a. To replace filtration tower back
into collection tank, drop into top of
collection tank and rotate counter-
clockwise so front of tower is facing
front of collection tank. Be sure to align
with tabs in bottom of collection tank.
b. Once water filtration tower is
replaced, replace cleaning mode selector
by inserting back into front of cleaner.
Make sure cleaning mode selector is in
“REMOVE” position when inserting back
into cleaner. Turn either clockwise to
“FILTER VAC” or counter-clockwise to
“WET CLEAN” to lock back in place.
8. For wet cleaning, remove all tools that
were used and rinse with clean tap water.
Allow to dry completely before storing.
9. The nozzle on the carpet deep cleaning
tool can be removed for a more thorough
clean.
a. Using a Phillips head screwdriver,
remove four screws from back side of
tool. Separate clear front nozzle from
back side of tool and rinse both parts
clean with running tap water. Allow to
air dry completely before reassembling.
b. To reassemble, place clear front
nozzle on to back side of tool by mating
cut out area at top of nozzle to black
tool holder, located on front top of back
side of tool. Press bottom of nozzle
so four screw bossed insert into screw
holes in back tool holder. Replace four
screws on back side of tool. Note two
long screws go into screw holes at
bottom of tool near brushes.
10. Remove hose and solution hose, taking
care to keep both ends of hose up to avoid
spilling any residual water. Empty out any
residual water in a sink water and rinse clean
with running tap water. Allow to air dry
completely before storing or placing back on
cleaner.
D-2 Machine maintenance
1. Pre-motor filter: Remove from top lid
by pulling tab away from separator and
pulling straight out. Remove foam filter
from separator and inspect. If dirty, rinse
with clean tap water and allow to air dry
completely before replacing back into
separator. To attach separator back onto
to top lid, line up “T” pieces under shallow
grooves on top lid and push together until
tab clicks together.
2. Post-Motor filter: Open filter door by
pressing down on latch and pulling down.
Once filter door is open, place one hand
on each side of filter and pull it out of
machine. If dirty, replace with new filter or
rinse under clean tap water and allow to air
dry completely before replacing back into
machine. Be sure filter door is fully closed
and latched prior to operating machine.
D-3 Machine storage
Water and cleaning formula can be left
in solution tank for next use.
1. Pull Quick Release cable wrap to left to
extend and wrap power cable.
2. Store unit in a protected, dry area, at
room temperature (4° to 43° C).
WARNING
TO REDUCE THE RISK OF FIRE AND
ELECTRIC SHOCK, ALWAYS INSTALL FLOAT
BEFORE ANY WET PICK-UP OPERATION.
www.BISSELL.com
10
EN
… 10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bissell Hydro Clean Pro Heat Complete 1474J at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bissell Hydro Clean Pro Heat Complete 1474J in the language / languages: English as an attachment in your email.

The manual is 3,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bissell Hydro Clean Pro Heat Complete 1474J

Bissell Hydro Clean Pro Heat Complete 1474J User Manual - English, German, Dutch, French, Italian, Polish, Swedish, Spanish - 100 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info